<h4>Pre-Installation Checklist</h4><ul><li>Replace oxygen, moisture and hydrocarbon traps as necessary.</li><li>Check gas cylinder pressures to ensure that an adequate supply of carrier, make-up and fuel gases are available. Carrier gases should be of the highest purity.</li><li>Ensure that the injection port is clean and free of sample residues, septum, or capillary debris.</li><li>Check and replace as necessary critical injector components such as seals, liners, and septa.</li><li>Check and replace detector seals as necessary.</li><li>Carefully inspect your column for damage or breakage.</li></ul>Note: It is critical that oxygen and water be removed from the carrier gas by the appropriate use of filters and adsorbents<h4>Injector Installation</h4>Note: GC columns do not have a specific directional flow when received from the manufacturer. Upon initial use of your new GC column, it is recommended to dedicate one specific end of the column for injector installation only. This is particularly important when dealing with active/caustic or contaminating compounds. If these compounds are routinely injected onto the column, degradation of the phase will occur—leading to higher bleed. A typical first step to remedying (removing) this bleed would be to trim 10 cm from the front (injector) end of the column and keep trimming this inlet end of the column as necessary. Trying to remedy any bleed issues by trimming the column may not work if both ends have been interchangeably installed into the inlet.<ol><li>Place a capillary nut and ferrule on the injector end of the GC column, allowing a section of column to protrude. Trim one to two centimeters from the protruding end to remove ferrule contamination that may have entered the column. Inspect the cut with a magnifier to ensure that a smooth, clean, square-cut edge has been made - recut if necessary.</li><li>Carefully hang the column in the GC oven, being cautious not to scratch or damage the polyimide coating on the capillary tubing. Rotate the column to avoid sharp bends of the capillary column and any contact of the column with oven surfaces.</li><li>Insert the column into the injector exactly the correct distance specified in the instrument manual. Tighten the ferrule nut finger-tight then 1/2 turn with a wrench. If the column can still be moved, tighten another 1/4 turn until the column is secure.</li><li>Adjust the carrier gas to obtain the flow rate listed on the test chromatogram.</li></ol>

Gas Chromatography (GC) Column Installation - Injector Installation

Each SPE mechanism/phase has a general set of solvent conditions under which SPE may be performed. Use the solvents/pH conditions listed below, volumes as determined in <a target="_blank" rel="noopener noreferrer" href="https://discover.phenomenex.com/0623-spe-technical-tip-part2-en?elqTrackId=E9D53E5725E641C0655E0409B9A065B7&amp;elq=00000000000000000000000000000000&amp;elqaid=4878&amp;elqat=2&amp;elqCampaignId=&amp;elqak=8AF59AC35AC6CFF8178E68A8DF72C3B8D482CF7C906A90E1BF5C55FDC1EA7D8B80B0">Method and Sorbent Volume Selection</a>.<h4>Reversed Phase SPE Method</h4><h5>Sorbent - SDB-L, C18, C8, PH, CN, X, XL</h5><ul><li>Analyte Properties: Low to moderate polarity (or nonpolar) Hydrophobic Neutralized/uncharged – Pharmaceuticals, Pesticides, Herbicides</li><li>Sample/Matrix: Aqueous, diluted with buffer – Biological fluids, Water</li><li>Conditioning Step<ul><li>Solvation – polar organic solvents – Methanol</li><li>Equilibration – aqueous, buffers – Water or buffer</li></ul></li><li>Wash Step: Aqueous buffers with 5 to 50 % polar organic solvent – Methanol:Water (5:95)</li><li>Elution Step: Polar or non-polar organic solvent(s) with or without water, buffer and/or strong acid or base – Methanol:Acetonitrile (50:50)</li></ul><h4>Normal Phase SPE Method</h4><h5>Sorbent - Silica, Florisil®, NH2, CN</h5><ul><li>Analyte Properties: Moderate to high polarity compounds (neutralized/uncharged) – Pesticides</li><li>Sample/Matrix: Non-polar organic solvents or moderately polar organic solvents – Hexane, chloroform, petroleum ether, toluene or methylene chloride</li><li>Conditioning Step<ul><li>Solvation – polar organic solvents (optional) – Methanol (optional)</li><li>Equilibration – sample/matrix solvent – Hexane or chloroform</li></ul></li><li>Wash Step: Non-polar organic solvents with a low concentration (1 to 5 %) of moderate to low polarity organic solvents – Hexane with 1 % THF, ethyl acetate, acetone, acetonitrile or IPA</li><li>Elution Step: Non-polar organic solvents containing higher concentrations (5 to 50 %) of moderate to high polarity organic solvents – Hexane with 10 % THF, ethyl acetate, acetone, acetonitrile or IPA</li></ul><h4>Strong Ion-Exchange SPE Method</h4><h5>Sorbet:&nbsp;Anion exchange: Screen-A, SAX, X-A, X-AW, XL-A, XL-AW Cation exchange: Screen-C, SCX, X-C, X-CW, XL-C, XL-CW</h5><ul><li>Analyte Properties: Ionized/charged compounds – Anion exchange: Acidic analytes Cation exchange: Basic drugs</li><li>Sample/Matrix: Aqueous; Low ionic strength buffers (&gt;30 mM), pH adjusted – Biological fluids plus buffer</li><li>Conditioning Step<ul><li>Conditioning – polar organic solvents – Methanol</li><li>Equilibration – low ionic strength buffers, pH adjusted – 25 mM Tris-OAc, pH 7</li></ul></li><li>Wash Step: Aqueous buffers of low salt concentrations with or without organic solvent<ul><li>Anion exchange: Buffer pH 7: Methanol (50:50)</li><li>Cation exchange:<ul><li>Buffer pH 6</li><li>1 M acetic acid</li><li>3. Methanol</li></ul></li></ul></li><li>Elution Step:<ul><li>Neutralize the charge on the weak anion or cation</li><li>Increase the ionic strength and counter ion concentration</li><li>Add a strong counter ion displacer<ul><li>Anion exchange: Hexane:ethyl acetate (75:25) + 1 % glacial acetic acid</li><li>Cation exchange: Methanol + 5 % NH₃</li></ul></li></ul></li></ul><blockquote>NOTE: These are general starting conditions. Please <a target="_blank" rel="noopener noreferrer" href="https://discover.phenomenex.com/customersupportEU?elqTrackId=9FD41A83311DD308567C001F2CC9485A&amp;elq=00000000000000000000000000000000&amp;elqaid=4878&amp;elqat=2&amp;elqCampaignId=&amp;elqak=8AF530A7A08EE95226A9F3C49828A74B76F7CF7C906A90E1BF5C55FDC1EA7D8B80B0">contact </a>your Phenomenex technical consultant for more assistance.</blockquote>

Generic SPE Method by Retention Mechanism

When installing your capillary GC column, making accurate connections is essential to ensure trouble free operation. In this technical tip we provide advice on the best way to achieve this.<blockquote>Note: For users with sensitive detectors such as MS and ECD, column conditioning steps should be performed before installing the column to prevent contamination and frequent maintenance of the detector.</blockquote>1) Place the column nut and ferrule past the end of the column and cut a centimeter or two off the end of the column. Be sure that the ferrule is the right size and pointing in the correct direction. Inspect the cut with a magnifier and ensure that the cut is square and smooth. See figure below. Recut if needed.2) Insert the outlet end of the column into the detector exactly the distance prescribed in the instrument manual. Distances will vary between detectors. Tighten the ferrule nut finger-tight then 1/2 turn with a wrench. If the column can still be moved, tighten another 1/4 turn until the column is secure.3) Inspect the column connections for leaks using an electronic leak detector. Leaks at the inlet end may introduce oxygen to the column that will result in increased column bleed and damage to the column phase.<img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Phenomenex_Gas_Chromatography_GC_Column_Installation_Detector_Installation_813b4d81a0.jpg" alt="Phenomenex: Gas Chromatography (GC) Column Installation - Detector Installation: Correctly and Incorrectly Cut GC Capillary." srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Phenomenex_Gas_Chromatography_GC_Column_Installation_Detector_Installation_813b4d81a0.jpg 245w," sizes="100vw" width="877" height="242">

Gas Chromatography (GC) Column Installation - Detector Installation

Normal phase SPE uses polar interactions as retention mechanism. These interactions include hydrogen bonding, dipole-dipole, induced dipole, π-π, etc. The interactions are between polar functional groups of analytes and polar sorbent chemistries.Reversed phase uses nonpolar, hydrophobic interactions as retention mechanism. These interactions include Van-der-Waals, London dispersion, π-π, etc. These interactions are between carbon rich, hydrophobic parts of both analytes and sorbent.When dealing with sample matrices that are only soluble in organic solvents, one would use a normal phase method. Examples of such matrices are oil, grease, or butter.Ideally, the sample is diluted with a nonpolar solvent (i.e. hexane) prior to sample loading. The sample can then be washed with hexane or 5% methylene chloride in hexane (analogous to washing with 5% MeOH in water in RP SPE methods to remove matrix interferences). Elution will be done with a polar solvent that can interrupt polar interactions between analytes and sorbent.Fractionation can be done by applying solvents in the order of increasing polarity or mixtures of solvents with different polarities.Below is a quick reference of solvents in ascending polarity, for Normal Phase SPE methods.<h3>Solvents in Polarity Order</h3><h5>From low to high&nbsp;</h5><ul><li>Hexane</li><li>Isooctane</li><li>Carbon tetrachloride</li><li>Toluene</li><li>Benzene</li><li>t-butyl methyl ether</li><li>Chloroform</li><li>Dichloromethane</li><li>Diethyl ether</li><li>Ethyl acetate</li><li>Tetrahydrofuran (THF)</li><li>Acetone</li><li>Acetonitrile</li><li>40% MeOH in acetonitrile</li><li>20% MeOH in diethyl ether</li><li>20% MeOH in dichloromethane</li><li>Isopropanol</li><li>Methanol</li><li>Water</li><li>Acetic acid</li></ul>

How is normal phase (NP) SPE different from reversed phase (RP) SPE? How do I decide which one to use?

Article

Product

Events

Webinars

Application

Academy

Video

Poster

Scientists

Plastics

Environment

Food

Water

Health

Presentation

Scientific article

Interview

Toxicology

Popularization

Science and research

Software

Covid-19

Career

Laboratories

Various

Zaměření

Type of News

Focus

Phenomenex is a global technology leader committed to developing novel analytical chemistry solutions that solve the separation and purification challenges of researchers in industrial, government and academic laboratories.

Phenomenex

LECO Training Course Pegasus BT/BT4D BTX/BTX4D

Markes International Symposium: Advances in GC sample introduction, separation and characterisation workflows

Current Trends in Forensic Toxicology Symposium (2026)

Modern Sample Prep for Organic Contaminants: PAHs, PFAS, MOSH/MOAH in Food

Uncovering Microplastics: Identification, Quantification, and Exposure Assessment

From Lab to Line: Leveraging GC and Process MS for Petrochemical Gas Analysis