Normal phase SPE uses polar interactions as retention mechanism. These interactions include hydrogen bonding, dipole-dipole, induced dipole, π-π, etc. The interactions are between polar functional groups of analytes and polar sorbent chemistries.Reversed phase uses nonpolar, hydrophobic interactions as retention mechanism. These interactions include Van-der-Waals, London dispersion, π-π, etc. These interactions are between carbon rich, hydrophobic parts of both analytes and sorbent.When dealing with sample matrices that are only soluble in organic solvents, one would use a normal phase method. Examples of such matrices are oil, grease, or butter.Ideally, the sample is diluted with a nonpolar solvent (i.e. hexane) prior to sample loading. The sample can then be washed with hexane or 5% methylene chloride in hexane (analogous to washing with 5% MeOH in water in RP SPE methods to remove matrix interferences). Elution will be done with a polar solvent that can interrupt polar interactions between analytes and sorbent.Fractionation can be done by applying solvents in the order of increasing polarity or mixtures of solvents with different polarities.Below is a quick reference of solvents in ascending polarity, for Normal Phase SPE methods.<h3>Solvents in Polarity Order</h3><h5>From low to high&nbsp;</h5><ul><li>Hexane</li><li>Isooctane</li><li>Carbon tetrachloride</li><li>Toluene</li><li>Benzene</li><li>t-butyl methyl ether</li><li>Chloroform</li><li>Dichloromethane</li><li>Diethyl ether</li><li>Ethyl acetate</li><li>Tetrahydrofuran (THF)</li><li>Acetone</li><li>Acetonitrile</li><li>40% MeOH in acetonitrile</li><li>20% MeOH in diethyl ether</li><li>20% MeOH in dichloromethane</li><li>Isopropanol</li><li>Methanol</li><li>Water</li><li>Acetic acid</li></ul>

How is normal phase (NP) SPE different from reversed phase (RP) SPE? How do I decide which one to use?

When considering the mass of sorbent required to perform a solid phase extraction it is critical to consider the sample matrix (serum, plasma, urine, saliva, food, river water, soil etc). This information will allow you, with the use of a suitable look up table to determine the mass of SPE sorbent to use. The tables are produced to reflect the relative levels of interfering endogenous material present in the samples.&nbsp;The SPE device must have enough capacity to retain all analytes of interest together with any endogenous materials capable of retaining on the sorbent with the same type of interactions as the analyte. If there is insufficient sorbent, it is possible some analyte may pass unretained through the SPE device during sample loading, leading to lower recoveries and a loss of consistency of recovery between samples.<h3>Sample Volume</h3><h4>Determines Bed Mass/ Solvent Volumes</h4><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Phenomenex_How_much_sample_can_I_load_onto_my_SPE_device_Is_it_linked_to_the_concentration_of_my_analyte_of_interest_12a9ab171c.jpg" alt="Phenomenex: How much sample can I load onto my SPE device? Is it linked to the concentration of my analyte of interest?" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Phenomenex_How_much_sample_can_I_load_onto_my_SPE_device_Is_it_linked_to_the_concentration_of_my_analyte_of_interest_12a9ab171c.jpg 154w," sizes="100vw" width="983" height="992"><h3>Generic Loading Capacities:</h3><h4>Polymeric: 10 - 15% of Total Bed Mass | Silica: 5% of Total Bed Mass</h4>If we compare plasma and urine, we can load 500 µl of plasma onto a 60 mg polymeric sorbent such as <a target="_blank" rel="noopener noreferrer" href="https://lcms.labrulez.com/products?manufacturerItems=50&amp;search=Strata-X">Strata™-X</a>. Using the same 60 mg SPE tube 2 mL of urine could be loaded, indicating that urine contains significantly less endogenous material than plasma.For sample types not included in the table, the use of generic loading capacity, 5% of sorbent mass for silica materials, or 10-15% for polymeric materials are advised. The difference between silica and polymeric sorbent loading capacity is a function of available surface area, which is higher for polymeric materials and also ligand density – the entire surface of a polymeric material is essentially stationary phase, while on a silica material only the phase bonded to the silica takes part in the extraction mechanism for reversed phase or ion exchange extractions.

How much sample can I load onto my SPE device? Is it linked to the concentration of my analyte of interest?

Article

Product

Events

Webinars

Application

Academy

Video

Poster

Scientists

Plastics

Environment

Food

Water

Health

Presentation

Scientific article

Interview

Toxicology

Popularization

Science and research

Software

Covid-19

Career

Laboratories

Various

Zaměření

Type of News

Focus

Phenomenex is a global technology leader committed to developing novel analytical chemistry solutions that solve the separation and purification challenges of researchers in industrial, government and academic laboratories.

How much sample can I load onto my SPE device? Is it linked to the concentration of my analyte of interest?

How is normal phase (NP) SPE different from reversed phase (RP) SPE? How do I decide which one to use?

Upcoming events

LECO Training Course Pegasus BT/BT4D BTX/BTX4D

SciY at analytica 2026

Waters Corporation at analytica 2026

Webinars

Trace the Threat: Py-GC/MS Workflows for Microplastics Characterization

FTIR microscopy: Practical guidance for effective sample analysis

Understanding Polymer Reactions and Degradation with FT-IR and EPR Spectroscopy