<p><strong>Concerns about injecting water into a GC system largely come from older column designs, where stationary phases were simply coated and could be affected by water exposure. Modern capillary columns are typically chemically bonded, which improves resistance to water injections and even supports water rinsing in many cases.</strong></p><p>One practical exception involves <strong>very polar polyethylene glycol </strong>(PEG / “wax”) phases. Because these phases strongly interact with water, repeated aqueous injections can allow water to accumulate and gradually shift selectivity. For many PEG-based columns, minimizing frequent water injections helps maintain consistent performance.</p><p>A separate—and often more important—issue is water’s<strong> very large vapor expansion in a hot inlet</strong>. If the vapor volume exceeds the inlet liner capacity, backflash can occur, sending sample vapor into cooler, unheated zones and increasing the risk of carryover. Using smaller injection volumes helps reduce this risk.</p><p>In workflows where water is the<strong> sample matrix </strong>(for example, volatile analysis), analytes may elute at relatively low oven temperatures while water and higher-boiling residues can linger. Periodic bake-off (high-temperature cleanup steps) is commonly used to restore column performance when water remains on the phase at low temperatures.</p><p>In summary, the biggest hesitation about water injections is rooted in legacy, coated column stories. With chemically bonded phases, the key considerations tend to be inlet expansion/backflash behavior, water retention on very polar phases, and routine maintenance practices like bake-out.</p><blockquote><h4><a target="_blank" rel="noopener noreferrer" href="https://gcms.labrulez.com/products/1571"><strong>Zebron ZB-WAX</strong><i><strong>PLUS</strong></i><strong> GC Columns</strong></a></h4><ul><li>100% aqueous stable, excellent for aqueous samples; bonded and solvent rinseable</li><li>Extremely inert for acidic compounds</li><li>Enhanced selectivity for low boiling solvents; high retention of alcohols and chlorinated solvents</li><li>Increased efficiency at 20&nbsp;°C</li></ul></blockquote>

Water in GC: Safe or Risky? Here’s What You Need to Know

<p><strong>🎤 Presenter:</strong> <strong>Paul-Albert Schneide </strong>(University of Copenhagen)</p><p>💾 <a target="_blank" rel="noopener noreferrer" href="https://gcms.labrulez.com/paper/32780"><strong>PDF presentation</strong></a></p><h3><strong>Abstract</strong></h3><p><strong>Tensor decomposition methods such as PARAFAC and PARAFAC2 have been proposed for resolving co-elutions, and extracting purified spectra in two-dimensional chromatography datasets. However, the application of these methods is usually restricted to local regions-of-interest (ROIs). Therefore, additional pre-processing steps, are required and processing multiple samples at once can be difficult due to retention time shifts (e.g., it is difficult to define a ROI that captures the same analyse signal in multiple samples).</strong></p><p>This work presents an application of fast, shift-invariant tensor decomposition, which was used for the decomposition of full-scale GCxGC-VUV datasets. The results show that chemical groups can be resolved, which are non-separable with conventional, template-based approaches, such as aliphates and olefines, Furthermore, the extracted peak areas are in good agreement with the quantitative results of the reference methods (e.g., bromine number for olefines).</p><h2><strong>Video Transcription</strong></h2><h3><strong>Background and Motivation</strong></h3><p>The project originated from a collaboration initiated by Alexandra Alvich from IFPEN, who approached Prof. Rasmus Bro’s research group at the University of Copenhagen for help analyzing a GC×GC-VUV dataset acquired during her PhD research. The work was then continued by Paul-Albert Schneider and Jesper Henri from the Technical University of Denmark.</p><p>The primary objective was to develop a simpler and less manually intensive approach for petrochemical group quantification while maintaining strong quantitative performance and spectral interpretability.</p><p>According to Schneider, the proposed method is based on two key principles:</p><ul><li>Simple implementation with a minimal number of tuning parameters</li><li>Accurate estimation of peak patterns, VUV spectra, and peak areas</li></ul><p>The workflow specifically targets group-level petrochemical analysis rather than individual compound identification.</p><h3><strong>Data Analysis Workflow</strong></h3><p>The presented workflow begins with a collection of GC×GC-VUV measurements. In this study, the researchers analyzed:</p><ul><li>14 gas oil samples</li><li>24 total measurements, including replicates</li><li>Samples processed using different treatment methods</li></ul><p>Initial preprocessing was performed using a dedicated plug-in module developed during Alexandra Alvich’s PhD work. The preprocessing included:</p><ul><li>Signal smoothing</li><li>Downsampling</li><li>Basic data conditioning</li></ul><p>The processed data were then submitted to the decomposition engine developed by the Copenhagen research group. The decomposition produced:</p><ul><li>Resolved VUV spectra</li><li>GC×GC chromatographic landscapes</li><li>Peak areas or peak volumes</li></ul><p>An in-house spectral library from IFPEN was subsequently used to verify that the extracted spectra corresponded to known petrochemical groups, enabling group-level quantitative analysis.</p><p>Importantly, the workflow currently requires only a single major tuning parameter: the number of components used in the decomposition model. The researchers also noted ongoing efforts to automate this selection step.</p><h3><strong>Comparison with Existing Template-Based Methods</strong></h3><p>The study benchmarked the new approach against Alexandra Alvich’s previously developed template-based quantification method.</p><p>In the template-based workflow:</p><ul><li>Elution regions are predefined using a grid structure</li><li>Peak intensities within those regions are summed</li><li>Quantitative estimates are obtained for specific petrochemical classes</li></ul><p>Although the template-based strategy demonstrated strong performance compared with other analytical techniques, Schneider highlighted several limitations:</p><ul><li>Sensitivity to retention time shifts</li><li>Manual adjustment of integration regions</li><li>Dependence on prior knowledge of coeluting compounds</li></ul><p>The new decomposition-based method was designed to reduce manual intervention and improve robustness against chromatographic variability.</p><h3><strong>Shift-Invariant Trilinear Decomposition</strong></h3><p>The proposed workflow is conceptually related to PARAFAC and multivariate curve resolution methods.</p><p>One important advantage of GC×GC-VUV data is the applicability of the Beer–Lambert law, which enables mathematically structured decomposition approaches.</p><p>The researchers evaluated two possible strategies:</p><ol><li>Decomposing each sample individually</li><li>Decomposing all samples simultaneously after concatenation into one large dataset</li></ol><p>The second strategy became the central focus of the work. Multiple samples were concatenated into a large matrix and factorized to extract shared chemical information across all measurements simultaneously.</p><p>Unlike many conventional GC×GC deconvolution pipelines, the workflow does not rely on a prior region-of-interest detection step. Instead, the entire dataset is decomposed directly.</p><h3><strong>Addressing Retention Time Shifts</strong></h3><p>A critical challenge for PARAFAC-type models is the assumption of strict trilinearity. In GC×GC datasets, however, second-dimension retention time shifts caused by temperature programming violate this assumption.</p><p>Schneider demonstrated how standard one-component PARAFAC models fail to properly model shifted peaks, leaving characteristic residual patterns. When fitting additional components, conventional models often allocate extra components to describing peak shifts instead of resolving true coeluting compounds.</p><p>The shift-invariant model solves this issue by explicitly accounting for chromatographic shifts. As a result:</p><ul><li>Large shifted peaks are modeled correctly</li><li>Residuals are minimized</li><li>Small coeluting peaks become resolvable</li></ul><p>The algorithm uses fast Fourier transform (FFT)-based operations internally to correct for chromatographic shifts efficiently.</p><p>According to the presentation, the approach is also significantly faster than PARAFAC2, which is commonly used for shifted datasets.</p><p>The researchers additionally described extensions of the model that can accommodate:</p><ul><li>Retention time shifts</li><li>Peak shape variations</li><li>Additional flexibility without losing uniqueness properties</li></ul><h3><strong>Quantitative Results</strong></h3><p>The team applied a seven-component model to the complete dataset containing 24 GC×GC-VUV measurements.</p><p>The decomposition extracted seven characteristic VUV spectra, which were compared against the IFPEN in-house spectral library. The extracted spectra matched known petrochemical group signatures very well.</p><p>The resolved components included:</p><ul><li>Two monoaromatic components</li><li>Two diaromatic components</li><li>Additional petrochemical group patterns</li></ul><p>For quantitative evaluation, chemically related components were grouped together.</p><h4><strong>Reproducibility</strong></h4><p>Replicate measurements demonstrated strong quantitative reproducibility:</p><ul><li>Relative standard deviations below 10%</li><li>Consistent peak area estimation across petrochemical groups</li></ul><h4><strong>Comparison with the Template-Based Approach</strong></h4><p>The decomposition workflow showed good agreement with the existing template-based quantification strategy, with monoaromatics representing the main discrepancy requiring further investigation.</p><p>Schneider explained that the differences were likely related to relative response factor scaling used in the template-based method but not yet implemented in the decomposition workflow at the time of the presentation.</p><h4><strong>Future Development</strong></h4><p>The researchers outlined several next steps for the project:</p><ul><li>Running models on individual samples to achieve higher resolution</li><li>Resolving sulfur-containing compounds</li><li>Extracting more sample-specific differences</li><li>Automating component number selection</li><li>Investigating deviations in monoaromatic quantification</li><li>Integrating the workflow into an open-source software project</li></ul><p>The team also expressed interest in future collaboration with other researchers working on related GC×GC data analysis workflows.</p><h3><strong>Conclusion</strong></h3><p>The presented shift-invariant trilinear decomposition workflow demonstrated promising performance for automated petrochemical group analysis in GC×GC-VUV datasets. By combining robust mathematical modeling with minimal manual intervention, the method offers a simplified alternative to traditional template-based approaches while maintaining strong quantitative agreement and spectral interpretability.</p><p>The work highlights the growing role of advanced multivariate data analysis strategies in comprehensive chromatography and demonstrates how shift-aware decomposition methods can significantly improve the analysis of highly complex petrochemical datasets.</p><blockquote><p><strong>This text has been automatically transcribed from a video presentation using AI technology. It may contain inaccuracies and is not guaranteed to be 100% correct.</strong></p></blockquote>

One-shot tensor decomposition of full-scale GC×GC-VUV datasets for resolving petrochemical groups (Paul-Albert Schneide, MDCW 2026)

<p><strong>Our Library never stops expanding. What are the most recent contributions to LabRulezGCMS Library in the week of 11th May 2026? Check out new documents from the field of the gas phase, especially GC and GC/MS techniques!</strong></p><blockquote><p><span style="font-size:20px;">👉 </span><a target="_blank" rel="noopener noreferrer" href="https://gcms.labrulez.com/library"><span style="font-size:20px;"><strong>SEARCH THE LARGEST REPOSITORY OF DOCUMENTS ABOUT GCMS AND RELATED TECHNIQUES</strong></span></a></p></blockquote><blockquote><p><strong>👉 Need info about different analytical techniques?</strong> Peek into <a target="_blank" rel="noopener noreferrer" href="https://lcms.labrulez.com/library"><strong>LabRulezLCMS</strong></a> or <a target="_blank" rel="noopener noreferrer" href="https://icpms.labrulez.com/library"><strong>LabRulezICPMS</strong></a> libraries.</p></blockquote><p>This week we bring you application note by<strong> Shimadzu, </strong>poster by <strong>MDCW / William &amp; Mary</strong> and brochure by <strong>Thermo Fisher Scientific!</strong></p><h3><strong>1. MDCW / William &amp; Mary: Optimizing Solvent Selection and Data Reduction Workflows for GC×GC Fire Debris Analysis</strong></h3><ul><li>Poster</li><li><a target="_blank" rel="noopener noreferrer" href="https://gcms.labrulez.com/labrulez-bucket-strapi-h3hsga3/P_14_O_Brien_63304669ee.pdf"><strong>Full PDF for download</strong></a></li></ul><section><div><div><div><div><div><div><h5><strong>What are Ignitable Liquid Residues (ILRs)?&nbsp;</strong></h5><ul><li>Chemical remains of ignitable liquids (IL) (e.g., gasoline or diesel) that did not fully burn during a fire&nbsp;</li><li>ILRs are usually petroleum-based products and contain complex mixtures of volatile chemicals, like hydrocarbons&nbsp;</li></ul><h5><strong>Forensic Analysis of ILRs&nbsp;</strong></h5><ul><li>Collection of porous materials like wood from the fire’s point of origin&nbsp;</li><li>Must be stored in airtight containers to prevent volatile ILR from evaporation&nbsp;</li><li>Passive headspace extraction onto activate charcoal strips (ACS) is used to extract ILRs from debris, and dichloromethane (DCM) is used to extracts ILRs from charcoal strips&nbsp;</li><li>Emerging is the use of two-dimensional gas chromatography – time of fight - mass spectrometry (GC×GC-TOFMS), with higher separation and resolution</li><li>Resulting chromatograms presents a pattern of peaks which can be used to identified specific type of accelerant used&nbsp;</li></ul><h5><strong>Chemometrics&nbsp;</strong></h5><ul><li>The discipline that focuses on the application of statistical and mathematical methods to analyze chemical data and extract meaningful information (Bovens, 2019)&nbsp;</li><li>Helps make sense of large datasets from analytical instruments, find pattens, and classify samples</li></ul><h4><strong>Methods</strong></h4><h5><strong>Analytical Instrumentation&nbsp;</strong></h5><ul><li>LECO corporation <a target="_blank" rel="noopener noreferrer" href="https://gcms.labrulez.com/products/1097"><strong>BTX4D GC×GC-TOFMS</strong></a> with <a target="_blank" rel="noopener noreferrer" href="https://gcms.labrulez.com/products/1289"><strong>Paradigm Shift reverse fill-flush (RFF) flow modulator</strong></a></li></ul><h5><strong>Software&nbsp;</strong></h5><ul><li><a target="_blank" rel="noopener noreferrer" href="https://gcms.labrulez.com/products/1873"><strong>ChromaTOF Sync 2D</strong></a> (LECO corporation)&nbsp;</li><li>R Statistical Software</li></ul><h4><strong>Conclusions</strong></h4><p>This study demonstrated that the use of chemometrics can be integrated into a data processing workflow to better understand data sets and create a streamlined process. Using UMAP, patterns identified that were not originally seen in PCA lead to the preferred solvents of ILR extraction being hexane and methanol. Since UMAP allowed visualization of local and global structures, groupings of gasoline samples allowed for better analysis of solvent effect.</p><h3><strong>2. Shimadzu: Multiresidue Pesticides Analysis in Solvent Extract of Annatto (Natural Color Additive) Using </strong><a target="_blank" rel="noopener noreferrer" href="https://gcms.labrulez.com/library?mainauthorItems=1&amp;search=GCMS-TQ8050+NX"><strong>GCMSTQ8050 NX</strong></a></h3><ul><li>Application note</li><li><a target="_blank" rel="noopener noreferrer" href="https://gcms.labrulez.com/labrulez-bucket-strapi-h3hsga3/an_06_sip_gc_043_en_95576a9ac4.pdf"><strong>Full PDF for download</strong></a></li></ul><h5><strong>User Benefits</strong></h5><ul><li>&nbsp;Accurate and reproducible trace level quantitation of pesticides in highly pigmented complex matrix using Ultra-fast GCMSTQ8050 NX and QuEChERS extraction</li><li>Single-laboratory partial validated method for LOQ determination meeting regulatory guidelines</li><li>Ease of instrumental method optimization using GCMS Smart Pesticides Database Ver.2 from Shimadzu Corporation</li></ul><p>Annatto is an orange-red condiment and food colorant derived from the seeds of the achiote tree (Bixa Orellana) (Fig. 1). It is often used to impart a yellow to red-orange color to foods, but sometimes also for its flavor and aroma. Similar effects can be obtained by extracting some of the color and flavor principles from the seeds, which are then added to the food. Annatto and its extracts are now widely used in an artisanal or industrial scale as a coloring agent in many processed food products, such as cheeses, butter, baked goods, potatoes, snack foods, breakfast cereals, smoked fish etc. In these uses, Annatto is a natural alternative to synthetic food coloring compounds.&nbsp;</p><p>Owing to its large culinary uses and other diverse applications, use of chemical pesticides for its production in large quantities is imperative. Dye extraction process may result in concentration of pesticides and in turn contribute to adverse impact on human health when incorporated in various preparations. Hence quantitation of residual pesticides in Annatto extract becomes very important. As the oleoresin is a complex matrix, it is required to develop a rugged, sensitive and efficient method for extraction of residual pesticide and its analysis.&nbsp;</p><p>This study reports a highly sensitive method for simultaneous quantification of multiple pesticides in highly pigmented complex matrix of Annatto using modified QuEChERS[1] with triple quadrupole gas chromatography (GC-MS/MS) system.</p><h4><strong>Materials and Methods</strong></h4><p>For this study, customized reference standard mixture of most commonly observed pesticides in Annatto seeds was procured from Restek Corporation.</p><p>The calibration standards were analyzed from 0.5 to 1000 μg/L. Linearity was plotted by external standard method and using weighted regression of 1/C2. Sample was spiked at 3 levels i.e., 10, 25 and 100 μg/kg. Recovery samples were prepared in 6 replicates at each level. <a target="_blank" rel="noopener noreferrer" href="https://gcms.labrulez.com/library?mainauthorItems=1&amp;search=GCMS-TQ8050+NX"><strong>GCMS-TQ8050 NX</strong></a> (Fig. 2), manufactured by Shimadzu Corporation Japan, was used for quantitation. LabSolutions InsightTM was used for data processing, which helped in evaluating validation parameters with ease.</p><h4><strong>Conclusion</strong></h4><p>This study shows that the modified QuEChERS method combined with GC-MS/MS system is a reliable and efficient tool to quantify residual pesticides in Annatto extract sample. Although Annatto extract is a highly pigmented complex matrix, the modified QuEChERS method significantly reduces interference. Also, extremely sensitive Shimadzu GC-MS/MS allows trace level detection even after multifold dilution of sample. This helps in reducing contamination and enhancing ruggednessresulting in reproducible detection of analytes.</p><h3><strong>3. Thermo Fisher Scientific: Sentinel PRO 710 environmental mass spectrometer Precise real time gas analyzer for toxic volatile organic compounds</strong></h3><ul><li>Product specification</li><li><a target="_blank" rel="noopener noreferrer" href="https://gcms.labrulez.com/labrulez-bucket-strapi-h3hsga3/sentinel_pro_710_spec_sheet_en_886523bfc2.pdf"><strong>Full PDF for download</strong></a></li></ul><p>The <a target="_blank" rel="noopener noreferrer" href="https://gcms.labrulez.com/library?mainauthorItems=3&amp;search=Sentinel+PRO"><strong>Thermo Scientific™ Sentinel PRO Environmental Mass Spectrometer </strong></a>is a highly reliable and versatile gas analyzer ideal for reporting the presence of toxic VOCs from fugitive emissions in industrial settings to ensure worker safety.</p><h4><strong>Fugitive emissions of toxic VOCs&nbsp;</strong></h4><p>Wherever there is potential danger for fugitive emissions of toxic organic vapors from a chemical production unit, regulating authorities often require plants to keep records of ambient vapor concentrations to protect workers from exposure. Various forms of capture include evacuated vessels, organic vapor monitors, or purge and trap devices, all of which require samples to be sent for analysis. Alternatively, electrochemical sensors or open path FT-IR spectroscopy can provide more immediate results. However, none of these technologies are capable of providing the spatial and temporal resolution required to qualify as actionable information.&nbsp;</p><h4><strong>Analytical platform&nbsp;</strong></h4><p>The primary feature of the Sentinel PRO mass spectrometer is the magnetic sector analyzer. This field-proven technology has demonstrated the strongest performance for industrial on-line gas analysis. Magnetic sector technology offers precision, accuracy, long intervals between calibrations. The new touchscreen interface further enhances usability, providing intuitive in-person operation, simplified maintenance, and real-time data viewing. Multi-role user permissions ensure security and control allowing operators to customize settings based on their specific needs.&nbsp;</p><h4><strong>Comprehensive data collection&nbsp;</strong></h4><p>With speed and precision, the Sentinel PRO analyzer monitors all the critical areas for short-term exposure levels of toxic VOCs, and also provides accurate and time-weighted average exposure data. With a high number of sample points available, many can be located close to potential leak points such as valve stems, etc., enabling leak detection and correction before any toxic hazard is created.&nbsp;</p><h4><strong>Membrane inlet mass spectrometry&nbsp;</strong></h4><p>The analyzer is fitted with a membrane inlet to reduce the pressure of the sample air from atmospheric to the working pressure of the enclosed ion source. This allows a method of sample introduction that greatly enhances the system’s sensitivity to VOCs. Since the membrane is more permeable to VOCs than to major air gases, it provides enrichment by several orders of magnitude, enabling detection as low as 5 ppb (species dependent) permits easy membrane replacement during annual routine maintenance to minimize downtime and increase productivity.</p></div></div></div></div></div></div></section>

News from LabRulezGCMS Library - Week 20, 2026

Article

Product

Application

Academy

Presentation

Video

Poster

The Multidimensional Chromatography (MDC) Workshop draws experts in this exciting field to share and discuss their research.

The Multidimensional Chromatography Workshop

Everything from the world of analytical chemistry in one place. We connect people in solving their problems. At Labrulez you will find all the necessary information easily, quickly and clearly. Stop searching and start finding.

LabRulez

Phenomenex is a global technology leader committed to developing novel analytical chemistry solutions that solve the separation and purification challenges of researchers in industrial, government and academic laboratories.

Phenomenex

Watrex xTrovert FLEX-O automation SPE sample preparation system

FLEX-O robotic system enabling automation sample preparation on solid phase using 96-titre plates.

<p><strong>FLEX-O robotic system enabling automation sample preparation on solid phase using 96-titre plates. Although there are solutions for automatic SPE on classic column formats, robotic system for automation in 96-well SPE plates is not currently on the market.</strong></p><p>In addition to <strong>the 8-channel pipetting head</strong>, the robot is equipped with <strong>a gripper</strong> and <strong>a filling dispenser</strong>, which applies wash solutions to the SPE positions on the plate. Instead of filtering using classic vacuum pump, which is used for manual SPE on columns or 96plates, the <a target="_blank" rel="noopener noreferrer" href="https://watrex.com/obchod/laboratory-automation/xtrovert-flex-o/?utm_source=labrulez&amp;utm_medium=propagace&amp;utm_campaign=labrulez_produkty"><strong>xTrovert FLEX-O</strong></a> system uses the so-called <strong>positive pressure technology</strong> when it is the reagent is pushed through the SPE membrane with a multi-channel pressure attachment. That’s it ensuring <strong>flow uniformity and reproducibility</strong> between individual samples on the plate.</p><p>The robot is capable of <strong>processing up to 4 x 96-well sample plates</strong> (384 of total samples) using a protocol with <strong>up to 8 different washing and extraction reagents</strong>.The system is <strong>compatible with the Waters OligoWorks™ SPE Macroplate</strong> (96-well), <strong>Waters Oasis™ PRiME HLB</strong>, <strong>Macherey-Nagel™ SPE MULTI 96-Monoblock CHROMABOND™</strong> and other 96-plate format SPE systems.</p><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Watrex_x_Trovert_FLEX_O_automation_SPE_sample_preparation_system_ec3768960e.jpg" alt="Watrex xTrovert FLEX-O automation SPE sample preparation system.jpg" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Watrex_x_Trovert_FLEX_O_automation_SPE_sample_preparation_system_ec3768960e.jpg 208w," sizes="100vw" width="1433" height="1075"></p><p>If necessary, the <strong>user can make modifications to the log</strong> using a simple scripting language and subsequent wireless upload to the device. Userthe interface for controlling the system is based on the integrated computer Raspberry Pi ® s 800×480 RGB LCD multi-touch touch screen and the possibility of remote wifi accessfrom an external device (e.g. mobile phone or tablet).</p><h4>Application</h4><ul><li><strong>Purification of oligonucleotide synthesis products</strong></li><li><strong>Organic Synthesis</strong></li><li><strong>Environmental Analysis</strong></li><li><strong>Medical diagnostics</strong></li><li><strong>Molecular biology and biochemistry</strong></li></ul><p>The entire system was designed and developed by Watrex Praha and is <strong>manufactured in the Czech Republic</strong> and promises a shift in the performance and efficiency of laboratory processes worldwide!</p>

Organomation 34 Position N-EVAP Nitrogen Evaporator

Our 34-position nitrogen evaporator (cat# 11634) offers a large number of sample positions, without compromising any of the classic N-EVAP features. 

<p><strong>Our 34-position nitrogen evaporator (cat# 11634) offers a large number of sample positions, without compromising any of the classic N-EVAP features. This time-tested, durable system provides one of the least expensive prices per position of all our N-EVAPs. The evaporative system, along with the standard flow control and pressure reducing regulator, enables the operator to achieve the desired level of concentration with efficient nitrogen usage. Our unique dual band spring hoist assembly ensures easy and effective operator use.</strong></p><p>Additionally, the 34 position N-EVAP includes a side control box, which provides timed and digitally controlled water bath temperatures to produce even evaporation rates. The pressure regulator and timer combine to allow timed automatic gas flow cut off which slows evaporation to a minimum once the timed cycle has been completed. In order to prevent damage to delicate samples, the timer also provides the option for the heat to shut off once the cycle is complete.</p><ul><li><strong>Gentle: </strong>N-EVAP nitrogen evaporators combine nitrogen blow down with a heated bath to gently concentrate delicate samples</li><li><strong>Flexible: </strong>An adjustable sample holder design fits a wide variety of sample tubes and vials at once</li><li><strong>Precise: </strong>Digital controls allow exact temperature regulation</li><li><strong>Individualized Control: </strong>Optimize evaporation of diverse samples with individual gas flow control at each vial</li></ul><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Organomation_34_Position_N_EVAP_Nitrogen_Evaporator_3_04176ee4e2.jpg" alt="Organomation 34 Position N-EVAP Nitrogen Evaporator." srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Organomation_34_Position_N_EVAP_Nitrogen_Evaporator_3_04176ee4e2.jpg 156w," sizes="100vw" width="1400" height="1400"></p><h3><strong>STANDARD FEATURES</strong></h3><ul><li>Nitrogen filter</li><li>Adjustable flow meter, 0-30 LPM</li><li>Built-in pressure reducing regulator</li><li>Side control box</li><li>Digital temperature controller</li><li>Electronic timer</li><li>Safety control cover plate</li><li>High pressure phthalate free tubing&nbsp;</li><li>High temperature limit switch for safety</li><li>Dual band spring hoist assembly&nbsp;</li><li>Precision needle valve tube assembly</li><li>Needles, 4 inch x 19 gauge with chrome plated brass hub and stainless steel shaft</li></ul><h3><strong>OPTIONS&nbsp;</strong></h3><ul><li>220v wiring harness (Option Code# -2), Cat# 111634-2</li><li>Z-Purge/positive pressure purge case (Option Code# -Z), Cat# 11634-Z</li><li>Acid resistant coating on instrument and needles (Option Code# -RT), Cat# 11634-RT</li></ul><h3><strong>SPECS</strong></h3><h4><strong>34 Position N-EVAP (Water Bath)</strong></h4><ul><li><strong>Bath Type</strong>: Water</li><li><strong>Instrumental Catalog Number</strong>: 11634</li><li><strong>Number of Sample Positions</strong>: 34</li><li><strong>Overall Dimension (w × d × h)</strong>: 24 × 19 × 34 in / 61 × 48 × 86 cm</li><li><strong>Sample Holder Layout</strong>: Circular</li><li><strong>Gas Manifold Layout</strong>: Single Ring</li><li><strong>Test Tube Range (Standard Sample Holder)</strong>: 10–30 mm OD</li><li><strong>Gas Flow Meter</strong>: 0–30 L/min</li><li><strong>Stainless Steel Needles (Length × Gauge)</strong>: 4.0 in × 19 ga / 102 mm × 19 ga</li><li><strong>Built-in Nitrogen Gauge Input</strong>: 30–110 psig</li><li><strong>Sample Tray Lift Mechanism</strong>: Dual Band Spring Hoist Assembly</li><li><strong>Rotating, Leak Tight Gas Fitting</strong>: Standard</li><li><strong>Acid Resistant Coating</strong>: Optional</li></ul><h5><strong>Heating Device Specs</strong></h5><ul><li><strong>Model Number</strong>: 13165</li><li><strong>Heating Medium</strong>: Water</li><li><strong>Inside Dimensions (Diameter × Depth)</strong>: 16.0 × 4.5 in / 40.6 × 11.4 cm</li><li><strong>Outside Dimensions (w × d × h)</strong>: 24 × 19 × 6 in / 61 × 48 × 15 cm</li><li><strong>Total Wattage</strong>: 1300 W</li><li><strong>Bath Temperature Range</strong>: 30–90 °C</li><li><strong>Temperature Controller Type</strong>: Digital Electronic with LED Display</li><li><strong>Controller Accuracy</strong>: ±2 °C</li><li><strong>Side Mounted Control Box with Timer for Nitrogen &amp; Heat</strong>: Standard</li></ul><h4><strong>34 Position N-EVAP (No Bath)</strong></h4><ul><li><strong>Bath Type</strong>: None</li><li><strong>Instrumental Catalog Number</strong>: 11634-O</li><li><strong>Number of Sample Positions</strong>: 34</li><li><strong>Overall Dimension (w × d × h)</strong>: 19 × 17 × 32 in / 48 × 43 × 81 cm</li><li><strong>Sample Holder Layout</strong>: Circular</li><li><strong>Gas Manifold Layout</strong>: Single Ring</li><li><strong>Test Tube Range (Standard Sample Holder)</strong>: 10–30 mm OD</li><li><strong>Gas Flow Meter</strong>: 0–30 L/min</li><li><strong>Stainless Steel Needles (Length × Gauge)</strong>: 4.0 in × 19 ga / 102 mm × 19 ga</li><li><strong>Built-in Nitrogen Gauge Input</strong>: 30–110 psig</li><li><strong>Sample Tray Lift Mechanism</strong>: Dual Band Spring Hoist Assembly</li><li><strong>Rotating, Leak Tight Gas Fitting</strong>: Standard</li><li><strong>Acid Resistant Coating</strong>: Optional</li></ul><h3><strong>MODELS</strong></h3><h5><strong>Catalog Number &nbsp;/&nbsp;&nbsp;&nbsp;Bath Type</strong></h5><ul><li>11634: <strong>Water</strong></li><li>11634-O: <strong>No Bath*</strong></li></ul><p><strong>*</strong>All “-O” models come with a base and stand assembly instead of a heated bath. These instruments are designed for evaporation procedures performed at ambient temperature.</p><h3><strong>ACCESSORIES</strong></h3><ul><li>Nitrogen generator (cat# NA1955)</li><li>Pasteur pipette adapters (cat# NA0636)</li><li>High temperature silicone fluid (cat# NA1240)</li><li>Various needle sizes and gauges</li></ul><h3><strong>REPLACEMENT PARTS</strong></h3><ul><li>P0627: <strong>Valve Tube Assembly</strong> – Post 1997</li><li>P0607:<strong> Luer &amp; washer for N-EVAP valve tube</strong></li><li>P0634: <strong>Tube Fitting nylon 3 part for N-EVAP valve tube</strong></li></ul>

Organomation 45 Position N-EVAP Nitrogen Evaporator

Our 45-position nitrogen evaporator offers the largest number of sample positions in our N-EVAP line. 

<p><strong>Our 45-position nitrogen evaporator (Catalog # 11645) offers the largest number of sample positions in our N-EVAP line. The sample holder has dual circular rings. The outer ring has 30 positions and can accommodate samples with an outside diameter of 10-19 mm The inner ring has 15 positions and can accommodate samples with an outside diameter of 16-30 mm and a minimum height of 70 mm.</strong></p><p>This time-tested, durable system provides the least expensive price per position of all our N-EVAPs. The evaporative system, along with the standard flow control and pressure reducing regulator, enables the operator to achieve the desired level of concentration with efficient nitrogen usage. Our unique dual band spring hoist assembly ensures easy and effective operator use. Additionally, the 45 position N-EVAP includes a side control box. Timed, digitally controlled water bath temperatures provide even evaporation rates. The pressure regulator and timer combine to allow timed automatic gas flow cut off which slows evaporation to a minimum once the timed cycle has been completed. The heat can also be shut off with the gas after a timed cycle.</p><ul><li><strong>Gentle: </strong>N-EVAP nitrogen evaporators combine nitrogen blow down with a heated bath to gently concentrate delicate samples</li><li><strong>Flexible: </strong>An adjustable sample holder design fits a wide variety of sample tubes and vials at once</li><li><strong>Precise: </strong>Digital controls allow exact temperature regulation</li><li><strong>Individualized Control: </strong>Optimize evaporation of diverse samples with individual gas flow control at each vial</li></ul><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Organomation_45_Position_N_EVAP_Nitrogen_Evaporator_5_20078e3969.jpg" alt="Organomation: 45 Position N-EVAP Nitrogen Evaporator." srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Organomation_45_Position_N_EVAP_Nitrogen_Evaporator_5_20078e3969.jpg 156w," sizes="100vw" width="1400" height="1400"></p><h3><strong>STANDARD FEATURES</strong></h3><ul><li>Nitrogen filter</li><li>Adjustable flow meter, 0-30 LPM</li><li>Built-in pressure reducing regulator</li><li>Side control box</li><li>Digital temperature controller</li><li>Electronic timer</li><li>Safety control cover plate</li><li>High pressure phthalate free tubing&nbsp;</li><li>High temperature limit switch for safety</li><li>Dual band spring hoist assembly&nbsp;</li><li>Precision needle valve tube assembly</li><li>Needles, 4 inch x 19 gauge with chrome plated brass hub and stainless steel shaft</li></ul><h3><strong>OPTIONS&nbsp;</strong></h3><ul><li>220v wiring harness (Option Code# -2), Cat# 11645-2</li><li>Z-Purge/positive pressure purge case (Option Code# -Z), Cat# 11645-Z</li><li>Acid resistant coating on instrument and needles (Option Code# -RT), Cat# 11645-RT</li></ul><h3><strong>SPECS</strong></h3><h4><strong>45 Position N-EVAP (Water Bath)</strong></h4><ul><li><strong>Bath Type</strong>: Water</li><li><strong>Instrumental Catalog Number</strong>: 11645</li><li><strong>Number of Sample Positions</strong>: 45</li><li><strong>Overall Dimension (w × d × h)</strong>: 24 × 19 × 34 in / 61 × 48 × 86 cm</li><li><strong>Sample Holder Layout</strong>: Circular</li><li><strong>Gas Manifold Layout</strong>: Dual Rings</li><li><strong>Outer Circle Sample Holder Test Tube Range</strong>: 10–19 mm OD</li><li><strong>Inner Circle Sample Holder Test Tube Range</strong>: 16–30 mm OD; &gt;70 mm height</li><li><strong>Gas Flow Meter</strong>: 0–30 L/min</li><li><strong>Stainless Steel Needles (Length × Gauge)</strong>: 4.0 in × 19 ga / 102 mm × 19 ga</li><li><strong>Sample Tray Lift Mechanism</strong>: Dual Band Spring Hoist Assembly</li><li><strong>Rotating, Leak Tight Gas Fitting</strong>: Standard</li><li><strong>Built-in Nitrogen Gauge Input</strong>: 30–110 psig</li><li><strong>Acid Resistant Coating</strong>: Optional</li></ul><h5><strong>Heating Device Specs</strong></h5><ul><li><strong>Model Number</strong>: 13165</li><li><strong>Heating Medium</strong>: Water</li><li><strong>Inside Dimensions (Diameter × Depth)</strong>: 16.0 × 4.5 in / 40.6 × 11.4 cm</li><li><strong>Outside Dimensions (w × d × h)</strong>: 24 × 19 × 6 in / 61 × 48 × 15 cm</li><li><strong>Total Wattage</strong>: 1300 W</li><li><strong>Bath Temperature Range</strong>: 30–90 °C</li><li><strong>Temperature Controller Type</strong>: Digital Electronic with LED Display</li><li><strong>Controller Accuracy</strong>: ±2 °C</li><li><strong>Side Mount Control Box with Timer for Nitrogen &amp; Heat</strong>: Standard</li></ul><h4><strong>45 Position N-EVAP (No Bath)</strong></h4><ul><li><strong>Bath Type</strong>: None</li><li><strong>Instrumental Catalog Number</strong>: 11645-O</li><li><strong>Number of Sample Positions</strong>: 45</li><li><strong>Overall Dimension (w × d × h)</strong>: 24 × 19 × 32 in / 61 × 48 × 81 cm</li><li><strong>Sample Holder Layout</strong>: Circular</li><li><strong>Gas Manifold Layout</strong>: Dual Rings</li><li><strong>Outer Circle Sample Holder Test Tube Range</strong>: 10–19 mm OD</li><li><strong>Inner Circle Sample Holder Test Tube Range</strong>: 16–30 mm OD; 70 mm height</li><li><strong>Gas Flow Meter</strong>: 0–30 L/min</li><li><strong>Stainless Steel Needles (Length × Gauge)</strong>: 4.0 in × 19 ga / 102 mm × 19 ga</li><li><strong>Sample Tray Lift Mechanism</strong>: Dual Band Spring Hoist Assembly</li><li><strong>Rotating, Leak Tight Gas Fitting</strong>: Standard</li><li><strong>Built-in Nitrogen Gauge Input</strong>: 30–110 psig</li><li><strong>Acid Resistant Coating</strong>: Optional</li></ul><h3><strong>MODELS</strong></h3><h5><strong>Catalog Number &nbsp;/&nbsp;&nbsp;&nbsp;Bath Type</strong></h5><ul><li>11645: <strong>Water Bath</strong></li><li>11634-O: <strong>No Bath*</strong></li></ul><p><strong>*</strong>All “-O” models come with a base and stand assembly instead of a heated bath. These instruments are designed for evaporation procedures performed at ambient temperature.</p><h3><strong>ACCESSORIES</strong></h3><ul><li>Nitrogen generator (cat# NA1955)</li><li>Pasteur pipette adapters (cat# NA0636)</li><li>High temperature silicone fluid (cat# NA1240)</li><li>Various needle sizes and gauges</li></ul><h3><strong>REPLACEMENT PARTS</strong></h3><ul><li>P0627: <strong>Valve Tube Assembly</strong> – Post 1997</li><li>P0607:<strong> Luer &amp; washer for N-EVAP valve tube</strong></li><li>P0634: <strong>Tube Fitting nylon 3 part for N-EVAP valve tube</strong></li></ul>

Waters Andrew+ pipetting robot

Andrew+ pipetting robot offers fully automated liquid handling using electronic pipettes and labware holders called Dominos.

<div data-id="7b8f701" data-element_type="widget" data-widget_type="heading.default"><div><h3><strong>Discover lab automation within reach</strong></h3></div></div><div data-id="c1b56fb" data-element_type="widget" data-widget_type="text-editor.default"><div><p><strong>Andrew+ pipetting robot offers fully automated liquid handling using electronic pipettes and labware holders called Dominos. By adding Device+, our ever-expanding portfolio of connected devices and tools for processes such as heating, shaking or labware transportation, Andrew+ evolves into a full walk-away automation solution.</strong></p><p>Creating the connected laboratory, Andrew+ is part of the&nbsp;<a target="_blank" rel="noopener noreferrer" href="https://www.andrewalliance.com/laboratory-software/"><strong>OneLab</strong></a>&nbsp;ecosystem, executing laboratory protocols designed in OneLab.&nbsp; This flexible architecture enables you to effortlessly transition from laborious manual pipetting procedures to error-free, fully-robotized lab workflows – without any knowledge of programming, laboratory robotics or automation engineering.</p><blockquote><p class="cke-user_style-important"><strong>Video: </strong><a target="_blank" rel="noopener noreferrer" href="https://www.youtube.com/watch?v=IGu3YxkkZY0"><strong>Andrew+ Demo</strong></a></p></blockquote><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Waters_Andrew_pipetting_robot_4_0569f8609e.jpg" alt="Waters Andrew+ pipetting robot" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Waters_Andrew_pipetting_robot_4_0569f8609e.jpg 245w," sizes="100vw" width="1440" height="540"></p><h3><strong>Andrew+ Case Studies&nbsp;</strong></h3><blockquote><p class="cke-user_style-important"><a target="_blank" rel="noopener noreferrer" href="https://www.andrewalliance.com/category/case-studies/"><span>See all case studies</span>&nbsp;</a></p></blockquote><div data-id="ee37b9e" data-element_type="widget" data-widget_type="heading.default"><div><h3><strong>Watch Andrew+ in action</strong></h3></div></div><div data-id="b265a33" data-element_type="widget" data-widget_type="text-editor.default"><div><p>In these videos, our biologists explain how Andrew+ enables users to automate commonly used, laborious, liquid handling for PCR Prep and Plasmid DNA Purification, respectively, whilst ensuring superior repeatability and full traceability.</p><blockquote><p class="cke-user_style-important"><strong>Video: </strong><a target="_blank" rel="noopener noreferrer" href="https://www.youtube.com/watch?v=RnxDri3Z7f4"><strong>PCR Prep</strong></a></p><p class="cke-user_style-important"><strong>Video: </strong><a target="_blank" rel="noopener noreferrer" href="https://www.youtube.com/watch?v=oWOkzqF9X9I"><strong>Plasmid DNA Prep</strong></a></p></blockquote><div data-id="fc9cb9e" data-element_type="column"><div><div data-id="cbb1a9b" data-element_type="widget" data-widget_type="heading.default"><div><h3><strong>Intuitive user interface</strong></h3></div></div><div data-id="3799119" data-element_type="widget" data-widget_type="text-editor.default"><div><div><div><div><div><div><p>Reproducibility and full traceability of sample preparation is assured using a highly intuitive browser-based software environment.&nbsp;<a target="_blank" rel="noopener noreferrer" href="https://www.andrewalliance.com/laboratory-software/"><strong>OneLab</strong></a> enables scientists to graphically design their own pipetting protocols in minutes and execute them straight away in any laboratory in the world, even allowing the remote monitoring of ongoing experiments. Use a flexible and secure platform that withstands the rigors of regulatory validation.</p><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Waters_Onelab_design_2_489d32ac68/Waters-Onelab-design-2_l.webp" alt="Waters-Onelab-design-2_l.webp" width="1027" height="488"></p><div data-id="9199ea6" data-element_type="column"><div><div data-id="6db85f8" data-element_type="widget" data-widget_type="heading.default"><div><h3><strong>Widest pipetting volume range</strong></h3></div></div><div data-id="ae0caea" data-element_type="widget" data-widget_type="text-editor.default"><div><p>Andrew+ pipetting robot uses single and multichannel electronic pipettes, ensuring the best liquid handling performance and maximum flexibility. Smart electronic pipettes are manufactured by Sartorius and based upon their acclaimed Picus pipettes.</p><p>Electronic pipettes are optimized for used with the Andrew+ pipetting robot, allowing greater flexibility in the type of liquid handling experiments that can be run, providing superior experiment reproducibility, pipetting speed and a market leading dynamic range of dispensing volumes for a liquid handing robot –from 0.2 µL up to 10 mL.</p><figure class="image"><img style="aspect-ratio:529/382;" src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Waters_Andrew_pipetting_robot_f5ca4f825d.jpg" alt="Waters Andrew+ pipetting robot.jpg" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Waters_Andrew_pipetting_robot_f5ca4f825d.jpg 216w," sizes="100vw" width="529" height="382"></figure><div data-id="ed235f6" data-element_type="column"><div><div data-id="ef6b933" data-element_type="widget" data-widget_type="heading.default"><div><h3><strong>Andrew+ is compact</strong></h3></div></div><div data-id="7537e2e" data-element_type="widget" data-widget_type="text-editor.default"><div><div><div><div><div><div><p>The liquid handling robot is designed to fit the majority of laboratory benches and biosafety cabinets (BSC). Andrew+, even with 2 full rows of Dominos&nbsp;<i>(</i>allowing to use 7 microplates or 56 falcon tubes or 168 microtubes) occupies a depth of ~55cm/22”, that fits even the smallest hoods. The unique compact size and design of our liquid handler allows it to work at a temperature of 20°C-37°C.&nbsp;</p><figure class="image"><img style="aspect-ratio:836/556;" src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Waters_Andrew_pipetting_robot_2_fb174b1453.jpg" alt="Waters Andrew+ pipetting robot - 2.jpg" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Waters_Andrew_pipetting_robot_2_fb174b1453.jpg 235w," sizes="100vw" width="836" height="556"></figure><div data-id="c9b37a7" data-element_type="widget" data-widget_type="heading.default"><div><h3><strong>Versatile working deck, tools and devices for all your needs</strong></h3></div></div><section data-id="b802f90" data-element_type="section" data-settings="{&quot;jet_parallax_layout_list&quot;:[]}"><div><div data-id="3e689f0" data-element_type="column"><div><div data-id="5dc9372" data-element_type="widget" data-widget_type="text-editor.default"><div><p>The Andrew+ deck layout is quickly adaptable to your experiment materials and are incredibly easy to set with the ever-expanding range of Dominos: a magnetic-based modular solution that enables Andrew+ to use a broad range of consumables.</p></div></div></div></div><div data-id="5626074" data-element_type="column"><div><div data-id="40c6ef1" data-element_type="widget" data-widget_type="text-editor.default"><div><p>In addition to pipetting liquids, the Andrew+ liquid handler can perform a wide range of complex experimental steps such as tube/plate transport or solid-phase extraction using vacuum.<br>Thanks to OneLab, you will benefit to a seamless integration of new capabilities added to your setting.</p><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Waters_Andrew_pipetting_robot_3_89b87a0d2e.jpg" alt="Waters Andrew+ pipetting robot - 3.jpg" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Waters_Andrew_pipetting_robot_3_89b87a0d2e.jpg 245w," sizes="100vw" width="1734" height="598"></p><div data-id="d090821" data-element_type="column"><div><div data-id="f9d733b" data-element_type="widget" data-widget_type="heading.default"><div><h3><strong>Automated Protocols with Andrew+</strong></h3><p>Specifically optimized for Andrew+, various applications and methods guarantee the delivery of better pipetting accuracy and improved reproducibility.</p><blockquote><ul><li><div><a target="_blank" rel="noopener noreferrer" href="https://onelab.andrewalliance.com/library/sars-cov-2-lc-ms-kit-ruo-9lwrvwkA"><span>Automated preparation of SARS-CoV-2 peptides for LC-MS analysis</span></a></div></li><li><div><a target="_blank" rel="noopener noreferrer" href="https://onelab.andrewalliance.com/library/automated-antibody-purification-jlwKQ0aY"><span>Automated Antibody Purification for higher recovery and reproducibility</span></a></div></li><li><div><a target="_blank" rel="noopener noreferrer" href="https://onelab.andrewalliance.com/app/lab/bl6MQP6z/library/standard-curve-generation-KlwRbwR3"><span>Reliable and Robust Sample Prep for Standard Curve Generation</span></a></div></li></ul><p class="cke-user_style-important"><a target="_blank" rel="noopener noreferrer" href="https://onelab.andrewalliance.com/library"><span><strong>More to discover in the Protocol Library</strong></span></a></p></blockquote><h3><strong>Get an extra pair of hands</strong></h3><div data-id="aa4715f" data-element_type="widget" data-widget_type="heading.default"><div><h4><strong>Reproducibility</strong></h4></div></div><div data-id="a1d2f3b" data-element_type="widget" data-widget_type="text-editor.default"><div><div><div data-animationtype="fadeInDown" data-animationduration="0.7" data-animationoffset="top-into-view"><div><p>Laboratory automation eliminates most human errors resulting in more reliable data and improved productivity. Together with complete integration inside OneLab, all experimental data from Andrew+ will be recorded and stored, improving the traceability of experiments and the data analysis.</p><div data-id="fb36639" data-element_type="widget" data-widget_type="heading.default"><div><h4><strong>Productivity</strong></h4></div></div><div data-id="c5f6abd" data-element_type="widget" data-widget_type="text-editor.default"><div><div><div data-animationtype="fadeInDown" data-animationduration="0.7" data-animationoffset="top-into-view"><div><div><div data-animationtype="fadeInDown" data-animationduration="0.7" data-animationoffset="top-into-view"><div><p>Andrew+ combines the flexibility of single channel pipetting (0.2 μL to 10 mL) with the higher throughput of multichannel pipetting. In addition, Andrew+ reduces the need to repeat experiments due to pipetting errors.</p><div data-id="0a035d7" data-element_type="widget" data-widget_type="heading.default"><div><h4><strong>Promoting health</strong></h4></div></div><div data-id="a72e364" data-element_type="widget" data-widget_type="text-editor.default"><div><div><div data-animationtype="fadeInDown" data-animationduration="0.7" data-animationoffset="top-into-view"><div><div id="applications"><div><div><div><div><div id="icon-area" data-animationoffset="top-into-view"><div><div data-animationtype="fadeInDown" data-animationduration="0.7" data-animationoffset="top-into-view"><div><p>Pipetting requires repetitive movements (of up to 500 times per day for the average user) that can lead to musculo-skeletal disorders like repetitive strain injury. Andrew+ helps eliminates physical stress to professionals, and also reduces the risk of exposure to hazardous materials used in certain experimental procedures.</p></div></div></div></div></div></div></div></div></div></div></div></div></div></div></div></div></div></div></div></div></div></div></div></div></div></div></div></div></div></div></div></div></div></div></div></div></section></div></div></div></div></div></div></div></div></div></div></div></div></div></div></div></div></div></div></div></div></div></div></div></div></div></div>

Thermo Scientific TriPlus™ RSH SMART Autosampler

Extend automation, performance, and versatility for GC and GC/MS applications, while ensuring easier and safer operations through SMART consumables ID recognition and usage tracking.

<div><div id="product-description"><p><strong>Expand automated sampling capabilities beyond liquid, headspace, and solid phase microextraction (SPME) injections. The advanced, built-in robotics of the Thermo Scientific™ TriPlus™ RSH SMART Autosampler deliver exceptional precision, sample handling flexibility, and reliable unattended operation. Enabling SMART consumables tracking, it offers easier, safer and traceable operations. Accurate and repeatable sample preparation and injection are essential to achieving the highest quality GC/GC-MS results. Enhance data quality and laboratory efficiency by automating your entire sample handling workflow.</strong></p></div><div><p>The TriPlus RSH SMART Autosampler brings together technological innovations that further expand automation, performance and versatility for GC and GC-MS applications, while ensuring easier and safer operations through SMART consumables ID recognition and usage tracking. Automated high-precision sample handling eliminates the manual labor and downtime typically required for tasks as standard/sample dilutions, internal standard addition and derivatization.</p><h3><strong>SMART Consumables</strong></h3><p>Validated SMART consumables are equipped with unique SMART chip storing parameters, ranges and usage history; enabling full traceability of sample preparation down to the syringe.</p><h3><strong>Automatic Syringe Changeout</strong></h3><p>Automatic Tool Change (ATC) capability automates the use of different syringes for sample preparation steps or different injection techniques within the sequence.</p><h3><strong>Vial Bottom Sensing Expands Application Range</strong></h3><p>Precise detection of vial bottoms enables the autosampler to accurately withdraw from sample amounts as little as 5 μL, enhancing data quality of sample-limited applications.</p><h3><strong>Flexible liquid sample handling</strong></h3><p>Optimized liquid injection modes and customizable syringe filling techniques, support a wide range of sample types and full GC inlet compatibility.</p><h3><strong>Automated headspace injection for volatile analysis</strong></h3><p>High temperature gas-tight syringe allows direct headspace injection into the GC inlet for increased injection volume flexibility. Sample vial capacity of up to 300x 10 mL/20 mL vials and sample incubation overlapping, facilitate long unattended operation.</p><h3><strong>Automated, solvent-free SPME</strong></h3><p>Precise control of all steps—fiber preconditioning, adsorption and desorption, as well as fiber washes—delivers maximum performance for SPME applications. Boost productivity with the optimized SPME Arrow design. It offers optimized fiber geometry to achieve 10x superior sensitivity compared to classical SPME, 2x faster extraction time and superior robustness.</p><h3><strong>Automated Sample Preparation</strong></h3><p>The Triplus RSH SMART Autosampler combines highly versatile sample injection capability with automated sample preparation procedures, eliminating typical GC-MS workflow bottlenecks. Daily operations ranging from sample/standard dilution to more complex derivatization protocols, can be fully automated and easily programmed with the Sampling Workflow Editor Software.</p><h3><strong>Extend productivity with the optional 1D barcode reader</strong></h3><p>The optional 1D barcode reader eliminates the need to log and track sample information manually; enabling you to streamline internal operations, save time, increase efficiency, and reduce errors.</p><h3><strong>Specifications</strong></h3><ul><li><strong>Type: </strong>TriPlus RSH SMART Standard Liquid, Regular Rail</li><li><strong>Sample Capacity:</strong> 4608 Well Plates, 840 x 0.5 mL or 0.7 mL Vials, 648 x 2 mL Sample Vials, 240 x 10 mL or 20 mL Vials</li><li><strong>Injection Mode: </strong>8 Fully Customizable Method-Specific Injection Mode Presets</li><li><strong>Injection Speed:</strong> Selectable from 0.1 μL/s to 2000 μL/s</li><li><strong>Injection Volume: </strong>0.1 to 10,000 μL</li><li><strong>Description: </strong>TriPlus RSH SMART configured for liquid injection on regular X-axis length. Only for manual tool change. Complete with liquid syringe tool, 2 x 10 μL SMART syringes, standard washing station and a single tray holder with 3 trays for 2 mL vials. Expandible to other sampling techniques (Headspace, SPME, SPME Arrow, ITEX-DHS) and with sample preparation tools.</li><li><strong>Tool Exchange:</strong> Only for manual tool exchange. No tool park station.</li><li><strong>For Use With (Equipment):</strong> Compatible with Smart syringes/fibers only.</li></ul></div></div>

Thermo Scientific™ TriPlus™ RSH Autosampler

Robotic GC autosampler with multimode injection, tool exchange, and full sample prep automation. Enables 24/7 workflows for food, environmental, and forensic labs.

<h4><strong>Flexible, high-capacity autosampler for GC and GC-MS with advanced sample prep automation</strong></h4><p><strong>The TriPlus RSH Autosampler is a versatile robotic sampling platform designed to maximize automation, precision, and productivity in gas chromatography workflows. Fully compatible with Thermo Scientific™ GC and GC-MS systems, it supports liquid, headspace (HS), and SPME/SPME Arrow injections, with optional modules for µSPE, ITEX-DHS, and automated sample preparation. The unique Automatic Tool Change (ATC) system allows the autosampler to switch between up to six syringes in a single sequence, enabling unattended workflows for complex multistep protocols.</strong></p><h3><strong>Key Features and Benefits</strong></h3><h4>🧪 <strong>Multimode Injection and Sample Handling</strong></h4><ul><li>Supports liquid, headspace, SPME, SPME Arrow, and ITEX-DHS techniques</li><li>Switch between injection modes in a single sequence using ATC</li><li>Bottom vial sensing enables precise injections from as little as <strong>5 μL</strong> of sample</li></ul><h4>🔁 <strong>Automated Sample Preparation</strong></h4><ul><li>Perform dilution, standard addition, derivatization, and internal standard workflows</li><li>Tools: Vortexer, Incubator, Heatex-Stirrer, Dilutor, µSPE module</li><li>Visual drag-and-drop <strong>Sampling Workflow Editor</strong> for custom prep protocols</li></ul><h4>📦 <strong>High Throughput and Capacity</strong></h4><ul><li>Unattended operation with up to <strong>972 × 2 mL vials</strong> or <strong>840 × 0.7 mL vials</strong></li><li>Extended X-arm option for larger trays and accessory support</li><li>Dual-GC configurations with Clone Mode or DoublePro setups</li></ul><h4>⚙️ <strong>Precision and Flexibility</strong></h4><ul><li>Automated Tool Change (ATC): Up to <strong>6 tools</strong> in one sequence</li><li>Injection volume range: <strong>0.1 μL to 10 mL</strong></li><li>Compatible with all major GC injector types (SSL, PTV, OC, PKD, PPKD)</li></ul><h4>🧠 <strong>Smart Software and Control</strong></h4><ul><li>Fully integrated with <a target="_blank" rel="noopener noreferrer" href="https://gcms.labrulez.com/products/76"><strong>Chromeleon™</strong></a>,<a target="_blank" rel="noopener noreferrer" href="https://lcms.labrulez.com/products/1758"><strong> Xcalibur™</strong></a>, and <strong>Chrom-Card™ CDS</strong></li><li>Local controller or virtual terminal control interface</li><li>Barcode readers for full sample tracking</li></ul><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/application::product.product/Thermo-TriPlus-RSH-Autosampler-1.jpg" alt="Thermo Scientific™ TriPlus™ RSH Autosampler" width="null" height="null"></p><h3><strong>Applications</strong></h3><ul><li><strong>Food safety</strong>: Trace analytes, contaminants, derivatization (e.g. FAMEs, dioxins)</li><li><strong>Environmental</strong>: VOCs, SVOCs, POPs, air toxics</li><li><strong>Forensics &amp; clinical</strong>: Biological matrices, explosive residues, drugs</li><li><strong>Chemical industry</strong>: Routine QC, trace impurities, residual solvents</li><li><strong>High-throughput labs</strong>: 24/7 unattended workflows with complex prep steps</li></ul><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/application::product.product/QExactive-GCMSMS-Orbitrap-with-Autosampler-sideangle-1856x1391.jpg-650.jpg" alt="Thermo Scientific™ TriPlus™ RSH Autosampler" width="null" height="null"></p>

Thermo Scientific Dionex AutoTrace 280 Solid-Phase Extraction Instrument

Extract analytes of interest from large volume aqueous samples easily and efficiently with the Thermo Scientific™ Dionex™ AutoTrace™ 280 Solid-Phase Extraction (SPE) Instrument.

<p><strong>Extract analytes of interest from large volume aqueous samples easily and efficiently with the Thermo Scientific™ Dionex™ AutoTrace™ 280 Solid-Phase Extraction (SPE) Instrument.&nbsp;</strong></p><p>The AutoTrace 280 automates all four steps of SPE (conditioning, loading, rinsing, and eluting), reducing solvent consumption and improving recovery and reproducibility. Boost productivity and reduce cost of analysis by simultaneously processing up to six samples in 2-3 hours with only 15 minutes of operator involvement. The AutoTrace 280 meets requirements in US EPA methods including the 500 and 600 series.</p><h5><strong>Improved reliability and recovery</strong></h5><ul><li>Automated SPE minimizes operator intervention</li><li>Positive pressure loading and elution of samples and solvents provide constant flow for improved analytical precision</li></ul><h5><strong>Flexibility in operation</strong></h5><ul><li>Loads sample volumes from 20 mL to 4 L</li><li>Compatible with 1, 3, and 6 mL cartridges and with 47 mm SPE disks</li><li>Automatically conditions, rinses, and elutes SPE cartridges with a choice of five solvents</li><li>Offers a choice of six different collection vial racks</li></ul><h5><strong>Improved laboratory safety</strong></h5><ul><li>Minimal sample handling reduces operator exposure to hazardous chemicals</li><li>No hood required</li></ul><h5><strong>Enhanced laboratory productivity and reduced costs</strong></h5><ul><li>Unattended operation</li><li>Batch processing of up to 6 samples</li><li>Reduced solvent usage</li><li>Segregates aqueous and solvent waste using separate waste lines for efficient, cost-effective waste handling</li></ul><h5><strong>Supports a range of matrices and applications</strong></h5><ul><li>Ability to process samples containing suspended solids</li><li>Meets requirements for solid-phase extraction for U.S. EPA methods including 500 and 600 series</li></ul><h5><strong>Recommended use</strong></h5><ul><li>Analyze prepared samples with Thermo Scientific LC or GC systems for a fully integrated workflow</li></ul><h4><strong>Specifications</strong></h4><ul><li><strong>Instrument Type:</strong> Automated Solid Phase Extraction (SPE) System</li><li><strong>Application:</strong> For use with 47 mm SPE disks</li><li><strong>Model Description:</strong> AutoTrace 280 SPE System</li></ul><h5><strong>Performance &amp; Operating Details</strong></h5><ul><li><strong>Disk Compatibility:</strong> Designed for 47 mm SPE disks</li><li><strong>Pressure Range:</strong><ul><li>Output: 0 to 30 psi (0 to 1.4 bar)</li><li>Input: Up to 100 psi (6.9 bar) maximum</li></ul></li><li><strong>Voltage:</strong> 100–240 V ±10%</li><li><strong>Frequency:</strong> 47–63 Hz</li></ul><h5><strong>Physical Specifications</strong></h5><ul><li><strong>Dimensions (D × W × H):</strong> 57 × 63.5 × 69 cm</li><li><strong>Unit Size:</strong> Each</li></ul>

Thermo Scientific EXTREVA ASE Accelerated Solvent Extractor

Achieve true walkaway sample-to-vial sample preparation with the Thermo Scientific™ EXTREVA™ ASE™ Accelerated Solvent Extractor. 

<p><strong>Achieve true walkaway sample-to-vial sample preparation with the Thermo Scientific™ EXTREVA™ ASE™ Accelerated Solvent Extractor. Without any intervention, perform sample extraction, in-cell cleanup and evaporation—all in one seamless operation—reducing manual labor from hours to minutes and enabling you to focus on other lab priorities while using up to 50% less solvent than other sample preparation techniques.</strong></p><p><strong>Accelerate your journey from sample to vial</strong></p><h5><strong>The EXTREVA ASE Accelerated Solvent Extractor offers:</strong></h5><ul><li><strong>All-in-one sample preparation.</strong> The EXTREVA ASE system automatically extracts and concentrates samples, eliminating the need to manually move sample extracts to another device for solvent evaporation.</li><li><strong>A walk-away solution. </strong>The system minimizes hands-on sample preparation tasks, enabling staff to accomplish other tasks.</li><li><strong>Parallel extraction. </strong>One EXTREVA ASE system can perform four parallel sample extractions, substantially increasing throughput.</li><li><strong>Gas-assisted extraction. </strong>The dynamic gas-assisted extraction mode reduces solvent consumption to between 5 and 100 milliliters per sample in most cases.</li><li><strong>Automation. </strong>Full automation improves recoveries and reproducibility while reducing training needs. Unlike humans, automated systems are ideal for performing the same tedious task repeatedly, and they don’t make mistakes.</li><li><strong>Method flexibility and optimization</strong>. Up to six different solvents can be used, including wash solvents for cleaning between methods. Precise flow control optimizes methods.</li><li><strong>Barcode-reading.</strong> The system tracks sample information and preparation parameters using a 2-D bar code reader to facilitate tracking and integrity. Data is recorded on the instrument or Thermo Scientific™ <a target="_blank" rel="noopener noreferrer" href="https://lcms.labrulez.com/products/76"><strong>Chromeleon™ Chromatography Data System (CDS) software</strong></a>.</li></ul><h4><strong>Specifications</strong></h4><ul><li><strong>Instrument Type:</strong> Automated Sample Preparation System</li><li><strong>Application:</strong> Simultaneous sample extraction and concentration</li><li><strong>Model Description:</strong> EXTREVA ASE Extraction and Evaporation System</li></ul><h5><strong>Performance &amp; Capabilities</strong></h5><ul><li><strong>Extraction Temperature Range:</strong> 40–200 °C</li><li><strong>Evaporation Temperature Range:</strong> 40–100 °C</li><li><strong>Compatible Solvents:</strong> Wide range of organic and aqueous solvents</li><li><strong>Pressure Capability:</strong> Up to 200 psi</li><li><strong>Power Consumption:</strong> 2000 W</li><li><strong>Frequency:</strong> 50/60 Hz</li></ul><h5><strong>Sample &amp; Solvent Handling</strong></h5><ul><li><strong>Extraction Cells (stainless steel):</strong> 1, 5, 10, 22, 34, 66, 100 mL</li><li><strong>Extraction Cell Tray:</strong> 16-position with 1 rinse</li><li><strong>Collection Vials:</strong><ul><li>60 mL and 100 mL evaporation vials</li><li>250 mL evaporation bottles</li><li>Direct concentrate to 2 mL sample vials with rinse capability</li></ul></li><li><strong>Collection Vial Tray:</strong> 16-position tray insert for 60 mL vials and 250 mL bottles; includes 4 rinse positions</li></ul><h5><strong>Utilities &amp; Requirements</strong></h5><ul><li><strong>Pneumatic Requirements:</strong><ul><li>Air: 130–140 psi</li><li>Nitrogen: 350–450 psi</li></ul></li></ul><h5><strong>Physical Specifications</strong></h5><ul><li><strong>Dimensions (D × W × H):</strong> 65.2 × 100 × 88.6 cm (25.6 × 39.4 × 34.8 in.)</li><li><strong>Weight:</strong> 160 kg (353 lb)</li><li><strong>Unit Size:</strong> Each</li></ul>

Thermo Scientific™ Dionex™ ASE™ 350 Accelerated Solvent Extractor

Save time, reduce solvent consumption, and boost productivity with Thermo Scientific™ Dionex™ ASE™ 350 Accelerated Solvent Extractor.

<div><p><strong>Automate extraction, filtration and clean up of compounds from solid and semisolid samples in minutes using the automated Thermo Scientific™ Dionex™ ASE™ 350 Accelerated Solvent Extractor. This system accommodates sample sizes of 1-100g, allows unattended extraction of up to 24 samples and uses 50 to 90% less solvent compared to other methods.&nbsp;</strong></p><p>The chemically inert pathway supports acid and alkaline sample matrices and solvents. Flexible, easy-to-operate and cost-effective, the Dionex ASE 350 is ideally suited for high-throughput laboratories and for a wide variety of applications.</p><div><h4><strong>Rapid and efficient extractions</strong></h4><ul><li>Elevated temperature (up to 200°C) and pressure (1500psi) reduce extraction times and solvent consumption</li><li>Fast pump (70mL/min.) enables fast extractions (typically 12-20 minutes)</li><li>Specialized oven design ensures precise temperature control for excellent reproducibility</li><li>Integrated solvent controller allows mixing and delivery of up to three solvents</li><li>The <strong>Thermo Scientific™ SmartRun™ System</strong> ensures cell size and collection vessel size are matched for an optimal extraction</li></ul><h4><strong>Enhanced flexibility to support multiple applications</strong></h4><ul><li>System accommodates <strong>1, 5, 10, 22, 34, 66 </strong>and <strong>100mL cell sizes</strong></li><li>pH-hardened pathway with <strong>Thermo Scientific™ Dionium™ components and cell</strong> enables compatibility with acid or alkaline pretreated matrices</li></ul><h4><strong>Dramatically reduced solvent consumption</strong></h4><ul><li>Requires less than 50mL solvent for a 20g sample</li><li>Includes solvent saver mode for further solvent savings</li></ul><h4><strong>Enhanced laboratory productivity</strong></h4><ul><li>System holds up to 24 samples for unattended operation</li><li>Flow-through technology allows in-line filtration and in-cell cleanup</li></ul><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Thermo_Scientific_Dionex_ASE_350_system_2_9426ff3f9a/Thermo-Scientific-Dionex-ASE-350-system_2.jpg" alt="Thermo Scientific™ Dionex™ ASE™ 350 Accelerated Solvent Extractor" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Thermo_Scientific_Dionex_ASE_350_system_2_9426ff3f9a/thumbnail_Thermo-Scientific-Dionex-ASE-350-system_2.jpg 114w," sizes="100vw" width="579" height="792"></p><h3><strong>🛠️ Specifications</strong></h3><ul><li><strong>Collection Vial Tray</strong>: 26-position tray insert for 60 mL vials; 19-position tray insert for 250 mL bottles</li><li><strong>Depth (English)</strong>: 27.3 in.</li><li><strong>Depth (Metric)</strong>: 69.3 cm</li><li><strong>Description</strong>: Extractor Only</li><li><strong>Extraction Fluids</strong>: Compatible with a wide range of organic and aqueous solvents</li><li><strong>Fluid Sensors</strong>: IR</li><li><strong>Frequency</strong>: 50/60 Hz</li><li><strong>Height (English)</strong>: 24.3 in.</li><li><strong>Height (Metric)</strong>: 61.7 cm</li><li><strong>Pneumatic Requirements</strong>: Air at 400–827 kPa (60–120 psi); N2 (at 1034 ×–1340 kPa (150–200 psi))</li><li><strong>Power Consumption</strong>: 500 Max VA</li><li><strong>Pressure</strong>: 10 MPa (1500 psi)</li><li><strong>Pump Flow</strong>: 70 mL/min</li><li><strong>Temperature Control</strong>: Up to 200 °C</li><li><strong>Weight (English)</strong>: 140 lb.</li><li><strong>Weight (Metric)</strong>: 65 kg</li><li><strong>Width (English)</strong>: 26.5 in.</li><li><strong>Width (Metric)</strong>: 67.3 cm</li><li><strong>Collection Vials</strong>: 60, 250 mL</li><li><strong>Dimensions (D x W x H)</strong>: 69.3 x 67.3 x 61.7 cm</li><li><strong>Extraction Cell Tray</strong>: 24 Cell, 2 Rinse</li><li><strong>Extraction Cells</strong>: 1, 5, 10, 22, 34, 66, 100 mL</li><li><strong>For Use With (Equipment)</strong>: Dionex ASE 350</li><li><strong>Type</strong>: Dionex ASE 350 System</li><li><strong>Unit Size</strong>: Each</li></ul></div></div>

LECO L-PAL3 GC Autosampler

LECO L-PAL3 GC Autosampler delivers flexible, discrimination-free GC injections with automated liquid, headspace, SPME, and ITEX sampling, high vial capacity, and minimal carryover.

<p><strong>Available exclusively from LECO, the L-PAL3 GC Autosampler is a highly robust, fully integrated autosampling platform designed for high flexibility and reliability in gas chromatography workflows. Based on proven CTC PAL3 technology, it supports discrimination-free ultrafast GC injections and minimizes carryover while ensuring precise and reproducible sample handling.</strong></p><p>Key innovations include <strong>automatic tool exchange (ATX)</strong> for seamless switching between liquid, headspace, SPME, and ITEX sampling modes, <strong>vial bottom sensing</strong> to prevent mis-injections, and high vial capacity for unattended operation. These features allow analysts to focus on compound identification without downtime or uncertainty.</p><h3><strong>Key Features</strong></h3><ul><li>Allows for automation of up to 162 two mL samples, or 45 ten/twenty mL samples.</li><li>Discrimination-free injection speeds with complete injection cycle time down to 100 milliseconds.</li><li>Bottom-sensing technology ensures that even very small volumes can be sampled.</li><li>Four separate models available so you may configure your package based on your autosampler needs.</li><li>Automatic Tool Exchange (ATX) allows users to switch between liquid, SPME, and headspace seamlessly.</li><li>96 to 384 well plate sampling supported; requires foil cutter.</li><li>Now available with Peltier cooled racks.</li></ul><h3><strong>Available Configurations</strong></h3><h4><strong>L-PAL3 GC Autosampler – Liquid Injections</strong></h4><ul><li>3-axis CTC-based autosampler/injector</li><li>Standard liquid injections</li><li>5-position solvent wash station</li><li>Liquid syringe tool</li><li>GC mounting kit</li><li>Single tray holder with <strong>3 trays × 54 positions (2 mL vials)</strong></li><li><strong>Non-upgradable configuration</strong></li></ul><h4><strong>L-PAL3 GC Autosampler – Liquid &amp; Headspace Injections</strong></h4><ul><li>Liquid and static headspace injections</li><li>Heated agitator</li><li>5-position solvent wash station</li><li>Liquid syringe tool + heated headspace syringe tool</li><li>GC mounting kit</li><li>Two tray holders:<ul><li><strong>3 × 54 positions (2 mL vials)</strong></li><li><strong>3 × 15 positions (10/20 mL vials)</strong></li></ul></li><li><strong>Manual tool exchange</strong> between liquid and headspace modes</li></ul><h4><strong>ITEX Dynamic Headspace Tool</strong></h4><ul><li>Rapid, sensitive enrichment of volatile and semi-volatile compounds</li><li>Suitable for solid, liquid, and gaseous samples</li><li>Choice of adsorbents for optimal sensitivity</li><li>No sample loops, transfer lines, or valves → minimal contamination risk</li><li>ATX enables <strong>Headspace, SPME, and ITEX</strong> within a single sequence</li></ul><h4><strong>L-PAL3 GC Autosampler – Liquid &amp; SPME Injections</strong></h4><ul><li>Liquid injections and all SPME modes (immersion, headspace)</li><li>Heated agitator</li><li>5-position solvent wash station</li><li>Liquid syringe tool + SPME fiber tools</li><li>SPME fiber conditioning station</li><li>GC mounting kit</li><li>Two tray holders:<ul><li><strong>3 × 54 positions (2 mL vials)</strong></li><li><strong>3 × 15 positions (10/20 mL vials)</strong></li></ul></li><li><strong>Manual tool exchange</strong> between liquid and SPME modes</li></ul><h3><strong>L-PAL3 GC Autosampler – Liquid, Headspace &amp; SPME</strong></h3><ul><li>Fully automated switching between liquid, headspace, and SPME</li><li>Heated agitator</li><li>5-position solvent wash station</li><li>Tools for liquid syringe, headspace syringe, and SPME fibers</li><li>SPME fiber conditioning station</li><li>GC mounting kit</li><li>Two tray holders:<ul><li><strong>3 × 54 positions (2 mL vials)</strong></li><li><strong>3 × 15 positions (10/20 mL vials)</strong></li></ul></li></ul>

Products from category Sample preparation automation - page 3

Related content

Water in GC: Safe or Risky? Here’s What You Need to Know

News from LabRulezGCMS Library - Week 20, 2026

One-shot tensor decomposition of full-scale GC×GC-VUV datasets for resolving petrochemical groups (Paul-Albert Schneide, MDCW 2026)