<blockquote>Welcome back to the topic of protecting your GC column! If you missed part 1 or would like to refresh your knowledge, find further tips on GC column protection <a target="_blank" rel="noopener noreferrer" href="https://www.phenomenex.com/knowledge-center/gc-knowledge-center/protecting-your-gc-column-pt1-tech-tip-en-1025">here.</a></blockquote>Protecting your GC column and instrument components from exposure to dirty samples or contaminants is important. Non-volatile or high molecular weight components can contaminate the stationary phase, causing poor peak resolution, lower accuracy, and poor column lifetime. Cutting off the damaged portion of column tubing will often restore your column’s performance, but over time performance will degrade to a point where the column can no longer be used. If you are experiencing rapid degradation of column performance, there are several simple ways to help protect your column and increase its lifetime.<h3>Use A Liner With Wool</h3>The liner is the first line of defense for your column, and the style you choose can make a big impact in how much contamination gets onto the column. The easiest thing to do is to add a small amount of silanized glass wool to a liner, which traps the non-volatile compounds and prevents them from entering directly into the column.&nbsp;<blockquote>Caution: glass wool can also add activity for acids, bases, and pesticides. Crushing the glass wool can expose undeactivated glass and free silanols (-OH groups) even if the wool has been deactivated. This leads to increased activity, so pre-packed liners, rather than self-packed ones are highly recommended to avoid reproducibility issues.</blockquote>In addition to choosing a liner with wool, ensure that your liner (and other system consumables) are free of contaminant build-up that may form over time. Septum cores and other particulates that remain can become trapped in the wool and are sometimes difficult to spot. Regularly replace the liner (and other system consumables as needed) to reduce troubleshooting and maintenance.<h3>Bake Out Your Column</h3>The easiest way to reduce column contamination is to add a short, high temperature bake-out at the end of your standard GC method. This bake out helps remove high boiling contaminants that would otherwise remain in the column and cause damage. To bake out, the final oven temperature needs to be set high enough to ensure elution of these compounds, but not so high as to cause thermal damage. This can be done either isothermally, or more commonly, via an oven ramp until the last components elute from the column. Caution: NEVER exceed the upper temperature limits of your column. DO NOT exceed more than fifteen minutes at the upper isothermal temperature limit specified for the column.

How to Protect Your GC Column - Part 2

<h3><a target="_blank" rel="noopener noreferrer" href="https://www.isc2026.org/">ISC 2026</a></h3>The <a target="_blank" rel="noopener noreferrer" href="https://lcms.labrulez.com/companies/314">International Symposium on Chromatography (ISC)</a> represents the oldest conference series on separation science. ISC symposia have been organised since 1956 in each even year. ISC is one of the premier meetings series for discussion of all modes of chromatography and separation science with a broad coverage of techniques and applications.The major focus of the symposium will be on the impact of chromatography and separation science to meet the needs of the pharmaceutical, environmental, food and health industry, as well as science and medicine. The symposium programme will reflect these themes and highlight new challenges and emerging opportunities for the science and marketing of separation and detection systems and methods.As an integral part of the scientific programme of lectures and poster sessions, an international exhibition and vendor seminars on instrumentation and services for chromatography, separation science and mass spectrometry will be organised. ISC 2026 will provide the perfect forum for attendees from academia, industry and government research institutions for scientific exchange and networking.<h3>ISC 2026 SYMPOSIUM KEY DATES</h3><h4>6-10 SEPTEMBER 2026</h4><ul><li>15 January 2026: Opening of Early-bird Registration &amp; Abstract submission</li><li>11 March 2026: Deadline for abstract submission (orals)</li><li>21 April 2026: Sending acceptance letters (orals)</li><li>15 May 2026: Deadline of early-bird registration and payment &amp; Author registration deadline (orals)</li><li>1 June 2026: Preliminary detailed program on web</li><li>1 June 2026: Deadline for abstract submission (posters)</li><li>16 June 2026: Sending acceptance letters (posters)<ul><li>Authors who submit their abstracts with a poster preference by 5 May 2026 will be notified of the outcome by 12 May 2026 and will have the opportunity to register at the early-bird rate until 15 May 2026.</li></ul></li><li>30 June 2026: Author registration deadline (posters)</li><li>30 July 2026: Deadline for abstract submission (late-breaking posters)<ul><li>without the possibility of competing for the Best Poster Award</li></ul></li><li>11 August 2026: Sending acceptance letters (late-breaking posters)</li><li>18 August 2026: Author registration deadline (late-breaking posters)</li><li>25 August 2026: Deadline for late registration &amp; payment&nbsp;</li><li>6-10 September 2026: Symposium</li></ul><h3>REGISTRATION</h3><blockquote>👉<a target="_blank" rel="noopener noreferrer" href="https://www.czech-in.org/cmPortalV15/Account/Login?ReturnUrl=%2FcmPortalV15%2FPortal%2FISC26%2Fnormal">Register HERE for the ISC 2026</a></blockquote><h3>ABSTRACT SUBMISSION</h3><blockquote>👉<a target="_blank" rel="noopener noreferrer" href="https://www.czech-in.org/cmPortalV15/Account/Login?ReturnUrl=%2FcmPortalV15%2FPortal%2FISC26%2Fnormal">Submit your Abstract HERE</a></blockquote><h3>SCIENTIFIC PROGRAM</h3><h4>SHORT COURSES</h4><h5>SC 3 Interpretation of Mass Spectra: Basic Introduction for Chromatographers</h5>🗓️ SUNDAY, 6 SEPTEMBER 2026🕗 8:30 – 11:45Mass spectrometry has become an essential tool in modern liquid chromatography, yet many chromatographers receive limited formal training in mass-spectral interpretation. This introductory short course provides a practical guide to understanding and interpreting mass spectra generated by the atmospheric-pressure ionization techniques coupled with LC: electrospray ionization (ESI), atmospheric-pressure chemical ionization (APCI), and atmospheric-pressure photoionization (APPI). The course begins by outlining the information that mass spectrometry adds beyond a chromatogram and clarifying which analytical questions mass spectrometry can – and cannot – answer. Participants receive a concise refresher on mass-spectrometric fundamentals, along with an introduction to key terminology. The principles and practical consequences of ionization methods are then discussed, with emphasis on how ionization physics, LC conditions, and mobile-phase additives shape spectral appearance. Building on this foundation, the course develops practical skills for interpreting LC-ESI spectra: locating the molecular ion, determining charge state, recognizing common adducts, distinguishing in-source artefacts, and using isotope patterns to support elemental-composition hypotheses. Participants then explore how MS/MS fragmentation provides structural clues, with straightforward rules of thumb for neutral losses and class-specific fragmentation behaviors. The course concludes with an integrative exercise that synthesizes chromatographic, full-scan, and MS/MS information to support spectral interpretation. By the end, participants will be equipped with the essential skills needed to interpret LC-MS spectra effectively and to apply mass-spectrometric reasoning in routine chromatographic analysis.&nbsp;<h4>Lecturers</h4><h5>Josef Cvačka</h5><ul><li>Josef Cvačka is head of the Mass Spectrometry Group at the Institute of <a target="_blank" rel="noopener noreferrer" href="https://lcms.labrulez.com/companies/62">Organic Chemistry and Biochemistry of the Czech Academy of Sciences</a> and an associate professor at the Faculty of Science, Charles University in Prague. His research focuses on the structural analysis of bioactive organic compounds using advanced mass-spectrometric techniques. He develops methods for pinpointing double-bond and methyl-branching positions in lipids and aims to discover new lipid classes in biological samples. His laboratory also designs new ion sources for MS and HPLC/MS. He teaches and supervises students at Charles University and founded the <a target="_blank" rel="noopener noreferrer" href="https://lcms.labrulez.com/articles?search=Czech+Museum+of+Mass+Spectrometry">Czech Museum of Mass Spectrometry</a>.</li></ul><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Josef_Cvacka_5cc8a0d1d4.jpg" alt="ISC 2026: Josef Cvačka" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Josef_Cvacka_5cc8a0d1d4.jpg 156w," sizes="100vw" width="510" height="510">

ISC 2026 Short Course 3 - Interpretation of Mass Spectra: Basic Introduction for Chromatographers

Our Library never stops expanding. What are the most recent contributions to LabRulezGCMS Library in the week of 9th February 2026? Check out new documents from the field of the gas phase, especially GC and GC/MS techniques!<blockquote>👉 <a target="_blank" rel="noopener noreferrer" href="https://gcms.labrulez.com/library">SEARCH THE LARGEST REPOSITORY OF DOCUMENTS ABOUT GCMS AND RELATED TECHNIQUES</a></blockquote><blockquote>👉 Need info about different analytical techniques? Peek into <a target="_blank" rel="noopener noreferrer" href="https://lcms.labrulez.com/library">LabRulezLCMS</a> or <a target="_blank" rel="noopener noreferrer" href="https://icpms.labrulez.com/library">LabRulezICPMS</a> libraries.</blockquote>This week we bring you technical note by Agilent Technologies, presentation by MDCW / University of Copenhagen and application notes by Shimadzu and Thermo Fisher Scientific!<h3>1. Agilent Technologies: What Causes Spots on <a target="_blank" rel="noopener noreferrer" href="https://gcms.labrulez.com/library?instrumentationItems=19&amp;manufacturerItems=1&amp;search=PLOT">PLOT Columns</a>? Will It Affect the Performance of the Column?</h3><ul><li>Technical note</li><li><a target="_blank" rel="noopener noreferrer" href="https://gcms.labrulez.com/labrulez-bucket-strapi-h3hsga3/te_what_causes_spots_plot_columns_affecting_performance_5994_8775en_agilent_3b7180512a.pdf">Full PDF for download</a></li></ul>Spots on porous layer open tubular (PLOT) columns are caused by small voids in the stationary phase coating inside the tube. These spots are areas where there is an uneven coating or lack of phase. It is normal to find some voids in the phase coating of PLOT columns. The stationary phase in PLOT columns is an opaque, solid, and porous material. In many Agilent PLOT columns such as the GS-Alumina phases, molecular sieves, porous polymers (Q and U), and the GS-OxyPLOT, the stationary phase is visible as a white powder. For many PLOT columns, the stationary phase fill solution is a viscous suspension of particles that are less than 10 microns in diameter. The phase is coated using a dynamic process in which a plug of fill solution is pushed through the tubing, and the plug’s speed and viscosity determines the thickness of the stationary phase layer. Once the PLOT’s stationary phase is deposited, it is held in place by electrostatic charge, chemical interactions between particles, and/or binding agents. In wall‑coated open tubular (WCOT) columns, stationary phases such as polysiloxanes or polyethylene glycols are immobilized by chemical bonding to the glass surface and cross-linking between polymer strands. Because this type of bonding and cross‑linking is not possible with PLOT phases, the result is a stationary phase layer that is both fundamentally different and inherently less stable in PLOT columns than in WCOT&nbsp;columns.<h3>2. MDCW / University of Copenhagen: One-shot tensor decomposition of full-scale GC×GC-VUV datasets for resolving petrochemical groups</h3><ul><li>Presentation</li><li><a target="_blank" rel="noopener noreferrer" href="https://gcms.labrulez.com/labrulez-bucket-strapi-h3hsga3/O_17_Schneide_67c8ff7866.pdf">Full PDF for download</a></li></ul>The presentation introduces a novel all-samples-at-once, shift-invariant tri-linear tensor decomposition approach for the analysis of full-scale <a target="_blank" rel="noopener noreferrer" href="https://gcms.labrulez.com/library?search=GC%C3%97GC-VUV">GC×GC-VUV</a> datasets, aimed at resolving and quantifying petrochemical groups. Traditional template-based or pixel-based methods struggle with retention-time shifts and co-eluting compounds, often requiring manual intervention and prior chemical knowledge. The proposed approach leverages the intrinsic low-rank structure of GC×GC-VUV data to enable robust, automated group-level analysis across multiple samples simultaneously.At the core of the method is a shift-invariant tri-linear model, conceptually related to PARAFAC and multivariate curve resolution, but extended using frequency-domain (FFT-based) modeling to explicitly account for chromatographic peak shifts. By decomposing the entire dataset in one step, the model provides accurate estimates of peak landscapes, VUV spectra, and relative peak areas, while remaining agnostic to retention-time variability. Importantly, the approach requires only a small number of tunable parameters, making it practical for routine use.The method was demonstrated on a case study involving 14 petrochemical gas-oil samples, including straight-run, hydrotreated, hydroconverted, coker, and light cycle oils. Extracted VUV spectra showed excellent agreement with reference spectra from a VUV spectral database, enabling confident assignment of components to chemical groups such as saturates, olefins, and mono- to poly-aromatics. Quantitative results exhibited high repeatability (RSD typically 3–9%) and strong correlation with established template-based reference methods.Overall, the work demonstrates that one-shot, shift-invariant tensor decomposition provides a powerful and scalable alternative to conventional GC×GC data-analysis strategies. By combining chemical interpretability, robustness to chromatographic shifts, and strong quantitative performance, the approach opens new opportunities for automated, high-confidence group-level analysis of complex petrochemical samples and beyond.<h3>3. Shimadzu: Py-Screener Ver. 3: Simultaneously Test for Substances Regulated Under RoHS, TSCA, and POPs</h3><ul><li>Application note</li><li><a target="_blank" rel="noopener noreferrer" href="https://gcms.labrulez.com/labrulez-bucket-strapi-h3hsga3/an_01_00949_en_4754e50164.pdf">Full PDF for download</a></li></ul><h5>User Benefits</h5><ul><li>In just one analysis, <a target="_blank" rel="noopener noreferrer" href="https://gcms.labrulez.com/library?manufacturerItems=3&amp;search=Py-Screener">Py-Screener</a> Ver. 3 can determine levels of phthalate esters, brominated flame retardants (PBBs, PBDEs), PIP (3:1), UV-328, dechlorane plus (DP), short-chain chlorinated paraffins (SCCPs), and medium-chain chlorinated paraffins (MCCPs).&nbsp;</li><li>It can also test for SCCPs and MCCPs by electron ionization (EI) instead of negative chemical ionization (NCI).&nbsp;</li><li>PIP (3:1), UV-328, DP, and SCCPs and MCCPs can be screened without the need for corresponding reference materials.</li></ul>Countries and regulatory bodies worldwide are introducing increasingly stringent regulations on the chemical substances used in electronic devices and industrial products. The RoHS Directive and REACH regulations in the EU, the Toxic Substances Control Act (TSCA) in the USA, and the Stockholm Convention on Persistent Organic Pollutants (POPs) are also targeting an increasingly broad range of substances. Therefore, manufacturers are required to accurately identify regulated substances in their products and comply with each regulation. While Py-Screener Ver. 2 can screen for seven phthalate esters and brominated flame retardants, including substances regulated under the RoHS Directive, version 3 can also screen for PIP (3:1), which is regulated under the TSCA, as well as UV328, DP, and SCCPs and MCCPs , which are regulated under the Stockholm Convention on POPs. A list of supported substances isshown in Table 1. This article introduces the simultaneous analysis of multiple regulated substances and a case study of testing specific regulated substances in samples, using Py-Screener Ver. 3.<h4>Analysis Process</h4>Py-Screener Ver. 3 can determine levels of phthalate esters and brominated flame retardants contained in products in accordance with the international analytical standards IEC62321-8 and IEC62321-3-3. It can also test for specific regulated substances (Table 1) under the same conditions and in the same analysis. In this test, background intensity and instrument sensitivity (S/N) were verified before analyzing samples. These parameters are prescribed by IEC62321-8 to ensure the accuracy of the methods used. Background intensity and instrument sensitivity were determined using a reference material (PN: 225-31003- 91) *1 that consisted of a plastic sheet that was spiked with seven phthalate esters. The results met the criteria for both parameters.The testing workflow is shown in Fig. 1. Before testing samples, calibration curves were prepared by analyzing the 1000 mg/kg phthalate ester reference material and polypropylene spiked with brominated flame retardants (ERM-EC591). A hole puncher was used to punch out two discs at a time of the phthalate ester reference material, and a cutter was used to obtain pieces of the other materials. Each material was weighed in a sample cup for analysis. During the analysis of samples, phthalate esters and some of the regulated brominated flame retardants were quantitated using a one-point calibration curve. The remaining brominated flame retardants and specific regulated substances were quantitated using the correction factor database*2 that is included with Py-Screener Ver. 3.<h4>Conclusion</h4>Py-Screener Ver. 3 successfully determined in samples the concentrations of the regulated substances PIP (3:1), UV-328, DP, and SCCPs and MCCPs. Normally, SCCP and MCCP levels are tested using NCI, but Py-Screener Ver. 3 uses EI. This enables it to test for not only SCCPs and MCCPs but also phthalate esters, brominated flame retardants, and other regulated substances in just one analysis. In addition, by using the relative correction factors linked to DEHP in the phthalate ester reference material, the levels of these regulated substances were determined without the need for the corresponding reference materials. Py-Screener Ver. 3 can also create a screening program that addresses substance restrictions under the RoHS Directive, the US TSCA, and the POPs Convention.<h3>4. Thermo Fisher Scientific: Improving low carbon steel production in specialty steel processes</h3><ul><li>Application note</li><li><a target="_blank" rel="noopener noreferrer" href="https://gcms.labrulez.com/labrulez-bucket-strapi-h3hsga3/prima_pro_process_mass_spectrometer_an1626_7fc840235f.pdf">Full PDF for download</a></li></ul>World crude steel production reached 1,691 million tonnes in 2017, up by 5.3% compared to 2016.1 While much of this capacity is still produced in primary steel processes such as basic oxygen furnaces and electric arc furnaces, the need for refined steel with greater durability and resistance to heat and corrosion has led to the increased use of vacuum degassing processes, such as VOD and RH, in secondary steel production. These processes are able to achieve ultra-low levels of residual carbon, while at the same time retaining desired levels of other alloy materials. If these processes are to achieve the required level of steel product quality, they need fast, continuous gas analysis of the furnace exhaust gas. Without accurate information on the composition of the gas leaving the furnace, any variations in the decarburization process are only detected after the event, resulting in the production of out-of-specification steel.<h4>Advantages of mass spectrometry&nbsp;</h4>Traditional Non-Dispersive Infra-Red (NDIR) analyzers are used in many conventional steelmaking processes to measure CO and CO2 , but they can only sample at atmospheric pressure. In vacuum steelmaking the process pressure changes dramatically, typically from atmospheric pressure down to less than 1 mbar, over the 20-30 minutes of the melt. So NDIR analyzers have to sample some distance downstream from the process. Analytical data is updated several minutes after the gas leaves the melt and the control system is forced to operate on historic rather than real-time data.&nbsp;Paramagnetic analyzers can be used to measure O2 , while thermal conductivity analyzers can be used to measure H2 . These analyzers also suffer from slow response, while the need to operate three different types of analyzers adds to the plant maintenance burden. Moreover, the three analyzers cannot analyze inert gases, so N2 is calculated by difference, a result that suffers from the sum of the errors of the three analytical techniques.&nbsp;Mass spectrometry operates at high vacuum so it is ideal for monitoring vacuum processes. It is also able to monitor all seven components in Table 1 in seconds rather than minutes, ensuring the plant control model is frequently updated with accurate compositional data.<h4>Precision of analysis&nbsp;</h4>At the heart of the <a target="_blank" rel="noopener noreferrer" href="https://gcms.labrulez.com/library?manufacturerItems=2&amp;search=Prima+PRO+Mass+Spectrometer">Thermo Scientific™ Prima PRO Mass Spectrometer</a> (MS) is a magnetic sector analyzer which offers unrivalled precision and accuracy compared with other mass spectrometers. Thermo Fisher Scientific manufactures both quadrupole and magnetic sector mass spectrometers; over thirty years of industrial experience have shown the magnetic sector based analyzer offers the best performance for industrial on-line gas analysis.&nbsp;Key advantages of magnetic sector analyzers include improved precision, accuracy, long intervals between calibrations, and resistance to contamination. Typically, analytical precision is between 2 and 10 times better than a quadrupole analyzer, depending on the gases analyzed and complexity of the mixture.&nbsp;A unique feature of the Prima PRO magnet is that it is laminated. Its analysis times are similar to a quadrupole analyzer, offering the unique combination of rapid analysis and high stability. This allows the rapid and extremely stable analysis of an unlimited number of user-defined gases. The scanning magnetic sector is controlled with 24-bit precision using a magnetic flux measuring device for extremely stable mass alignment.&nbsp;The ion source is an enclosed type for high sensitivity, minimum background interference, and maximum contamination resistance. This is a high-energy (1000 eV) analyzer that offers extremely rugged performance in the presence of gases and vapors that have the potential for contaminating the analyzer. Typical performance specifications for the Prima PRO MS are shown in Table 1. Analytical performance is demonstrated by analyzing the calibration bottle over 1 hour following calibration, with an analysis time of just 6 seconds. Standard deviations measured on the calibration cylinder will be equal to or better than the stated values.

News from LabRulezGCMS Library - Week 07, 2026

Article

Events

Application

Academy

Presentation

Everything from the world of analytical chemistry in one place. We connect people in solving their problems. At Labrulez you will find all the necessary information easily, quickly and clearly. Stop searching and start finding.

LabRulez

Phenomenex is a global technology leader committed to developing novel analytical chemistry solutions that solve the separation and purification challenges of researchers in industrial, government and academic laboratories.

Phenomenex

The International Symposium on Chromatography (ISC) represents the oldest conference series focussing on separation science. ISC symposia have been organised since 1956 in each even year. ISC is internationally recognised as one of the premier meeting series for discussion of all modes of chromatography and separation science with a broad coverage of techniques and applications.

International Symposium on Chromatography - (ISC)

Agilent Technologies

Technology Networks

ACD/Labs

SepSolve Analytical

LECO

OpenLab CDS contains a very powerful reporting engine built on the industry standard of Microsoft’s Business Intelligence Studio. It affords an opportunity to create customized reports that minimize or eliminates a laboratory’s dependence on excel. This session will introduce users to the types of reports Agilent includes with the software, along with how to customize those reports to include your own calculations.
<blockquote>
Presenter: Richard Mutkoski (Laboratory Informatics Application Engineer, Agilent Technologies, Inc.)
</blockquote>
<blockquote>
Richard Mutkoski began with Agilent (HP) in 1995. He has been an Application Engineer in Agilent’s Laboratory Informatics for the past 16 years. Prior to his career at Agilent Rich spent 12 years in a variety of small pharmaceutical firms in both R&amp;D and QA/QC capacities affording him first-hand knowledge of those workflows, bottlenecks and challenges.
</blockquote>

Agilent Technologies: Introduction to OpenLab CDS Custom Reporting

Introduction to OpenLab CDS Custom Reporting

This demonstration will concentrate on the enhanced workflows and capabilities of OpenLab CDS.
<h3>During this 1-hour session you will:</h3>
<ul>
<li>Learn about the function and advantages of the new control panel including creating instruments, creating projects, activity logs, storage types and paths.</li>
<li>Explore the basic operations of user privileges including assigning permissions and roles, and license utilities.</li>
<li>Learn the basics of how to setup instruments, methods and sequences.</li>
<li>Explore the enhanced data processing workflow including auto and manual integration, e-signatures and audit trail review</li>
<li>Discover uses for the Custom Calculator and its functionality</li>
<li>Learn how to customize reports with the Intelligent Reporter to generate calculations without to use of Excel</li>
</ul>
<blockquote>
Presenter: Richard Mutkoski (Application Engineer, Agilent Technologies, Inc.)
</blockquote>
<blockquote>
Richard Mutkoski began with Agilent (HP) in 1995. He has been an Application Engineer in Agilent’s Laboratory Informatics for the past 16 years. Prior to his career at Agilent Rich spent 12 years in a variety of small pharmaceutical firms in both R&amp;D and QA/QC capacities affording him first-hand knowledge of those workflows, bottlenecks and challenges.
</blockquote>

Agilent Technologies: OpenLab CDS Introductory Demonstration

OpenLab CDS Introductory Demonstration

The Control Panel is the gatekeeper to the system.
<ul>
<li>Learn how to enable authentication to allow chemist names to be placed on reports. </li>
<li>See how to configure system in a compliant environment and restrict users’ access to instruments and data. </li>
<li>Understand the use of Roles and Privileges to refine what users can do. </li>
<li>Understand the need, creation and use of Projects. </li>
<li>Explore how to set-up an Acquisition Method for a Virtual 3D HPLC and a Virtual 7890 GC. </li>
<li>Explore the software features that have been designed to help minimize sequence creation time and eliminate costly typographical errors.</li>
</ul>

Agilent Technologies: OpenLab CDS Virtual Masterclass Series

OpenLab CDS Virtual Masterclass Series Session 1 - The Control Panel and Data Acquisition

Přednáška prof. Olivera Fiehna v rámci ASMS 2019 na téma použití online metabolomických databází, možnosti LECO Pegasus vs. BT nebo nástrojů jako BinBase, BinView, MassBank.us a MS-FINDER.
<blockquote>
Presenter: Oliver Fiehn (Director West Coast Metabolomics Center, Davis, California)
</blockquote>

LECO/Oliver Fiehn: Using Open Access Online Metabolomic Databases with LECO GC-TOF MS instruments

Using Open Access Online Metabolomic Databases with LECO GC-TOF MS instruments

<h3>Webinar Summary</h3>
Often there is a natural trade-off between IT demands, such as reducing the number of different systems in use (standardization) or leveraging modern technologies (like cloud), and the increased productivity and compliance demands for your laboratory.
This compromise is now over. Learn how Thermo Scientific™ Chromeleon™ 7.3 Chromatography Data System (CDS) is the first CDS to truly meet the needs of both the IT and infrastructure team and the laboratory.
Now you can standardize without compromise with global deployment, system stability and data security, and still realize significant laboratory productivity gains!
<h3>Attend this webinar to learn how Chromeleon™ 7.3 CDS:</h3>
<ul>
<li>Can deliver productivity gains of up to a third</li>
<li>Leverages modern IT technologies to ensures business continuity and streamlining in deployment and leveraging modern IT technologies</li>
<li>Offers new features that will be invaluable to your lab</li>
</ul>
<blockquote>
Presenter: Darren Barrington-Light, Senior Manager Product Marketing, Thermo Fisher Scientific™
</blockquote>

Technology Networks: The New No-compromise Enterprise CDS Solution

The New No-compromise Enterprise CDS Solution

Improvements in mass spectrometry have generated an increasing demand for analysis of more complicated samples by mass spectrometry (MS). While liquid chromatography (LC) and gas chromatography (GC) are effective at reducing sample complexity, co-elution of components is still not entirely avoidable. The reality of today&#39;s lab is:
<ul>
<li>A variety of instrument configurations and a multitude of software interfaces</li>
<li>Mountains of complex data for analysis</li>
</ul>
Struggle no more!
Join us to learn how vendor-neutral software can help you deformulate samples more efficiently leveraging knowledge from both the wider scientific community and your organization. See how third-party software enables you to:
<ul>
<li>Separate co-eluting components</li>
<li>Identify known and unknown components</li>
<li>Store, share, and leverage expertise</li>
</ul>
Hear about recent enhancements to these tools and see a sneak-peek of enhancements yet to come.
<h3>Intended Audience</h3>
<ul>
<li>Mass Spectrometrists</li>
<li>Analytical Chemists</li>
<li>Analytical Lab Managers/Directors</li>
</ul>
<blockquote>
Presenter: Anne Marie Smith, Senior Application Scientist at ACD/Lab
</blockquote>
<blockquote>
She received her Ph.D. in Chemical Biology from McMaster University where she developed MALDI-MS based assays for screening aminoglycoside kinases. After graduating she was employed as an Associate Scientist with Gilead Sciences in Alberta where her work focused primarily on impurity identification by LC/MS and LC method development. At ACD/Labs Anne Marie applies her hands-on experience with MS instruments and scientific software packages, plus knowledge of chromatographic method validation, to help customers implement our MS solutions and troubleshoot any technical challenges.
</blockquote>
<blockquote>
Host: Sanji Bhal is the Director of Marketing &amp; Communications at ACD/Labs.
</blockquote>
<blockquote>
Prior to joining ACD/Labs she was a lab-coat wearing medicinal chemist at Signalgene Inc., where she pursued her ongoing interest in cancer research, followed by a stint with the CRO NAEJA Pharmaceuticals. Sanji began her career in the U.K., completing her Ph.D. in synthetic organic chemistry at the University of Reading, and a post-doctoral fellowship at Cancer Research UK. Today Sanji is passionate about understanding the challenges still faced by scientists and R&amp;D organizations, and helping to &#39;match-make&#39; their needs with the tools available to support their innovations.
</blockquote>

Pixabay/Gerd Altmann:  Practical Steps for Efficient Deconvolution of LC/MS and GC/MS Data for Deformulation

 Practical Steps for Efficient Deconvolution of LC/MS and GC/MS Data for Deformulation

<h3>In this webinar you will:</h3>
<ul>
<li>See our simple workflows for GC and GCxGC processing on a range of file formats</li>
<li>Hear about our hardware support for streamlined instrument control and data processing </li>
<li>Find out how our network licensing can unify lab processing </li>
<li>Discover the latest features of the soon-to-be-released v1.5</li>
</ul>

SepSolve: The latest innovations in GCxGC software: What can ChromSpace do for you?

GCMS webinars focusing on Software - page 34