<blockquote><p>Welcome back to the topic of protecting your GC column! <strong>If you missed </strong><a target="_blank" rel="noopener noreferrer" href="https://gcms.labrulez.com/article/6766"><strong>part 1</strong></a> or would like to refresh your knowledge, find further tips on GC column protection <a target="_blank" rel="noopener noreferrer" href="https://www.phenomenex.com/knowledge-center/gc-knowledge-center/protecting-your-gc-column-pt1-tech-tip-en-1025"><strong>here</strong>.</a></p></blockquote><p><strong>Protecting your GC column and instrument components from exposure to dirty samples or contaminants is important. Non-volatile or high molecular weight components can contaminate the stationary phase, causing poor peak resolution, lower accuracy, and poor column lifetime. Cutting off the damaged portion of column tubing will often restore your column’s performance, but over time performance will degrade to a point where the column can no longer be used. If you are experiencing rapid degradation of column performance, there are several simple ways to help protect your column and increase its lifetime.</strong></p><h3><strong>Use A Liner With Wool</strong></h3><p>The liner is the first line of defense for your column, and the style you choose can make a big impact in how much contamination gets onto the column. The easiest thing to do is to add a small amount of silanized glass wool to a liner, which traps the non-volatile compounds and prevents them from entering directly into the column.&nbsp;</p><blockquote><p><strong>Caution: </strong>glass wool can also add activity for acids, bases, and pesticides. Crushing the glass wool can expose undeactivated glass and free silanols (-OH groups) even if the wool has been deactivated. This leads to increased activity, so pre-packed liners, rather than self-packed ones are highly recommended to avoid reproducibility issues.</p></blockquote><p>In addition to choosing a liner with wool, ensure that your liner (and other system consumables) are free of contaminant build-up that may form over time. Septum cores and other particulates that remain can become trapped in the wool and are sometimes difficult to spot. Regularly replace the liner (and other system consumables as needed) to reduce troubleshooting and maintenance.</p><h3><strong>Bake Out Your Column</strong></h3><p>The easiest way to reduce column contamination is to add a short, high temperature bake-out at the end of your standard GC method. This bake out helps remove high boiling contaminants that would otherwise remain in the column and cause damage. To bake out, the final oven temperature needs to be set high enough to ensure elution of these compounds, but not so high as to cause thermal damage. This can be done either isothermally, or more commonly, via an oven ramp until the last components elute from the column. Caution: NEVER exceed the upper temperature limits of your column. DO NOT exceed more than fifteen minutes at the upper isothermal temperature limit specified for the column.</p>

How to Protect Your GC Column - Part 2

<p>🎤 <strong>Presenter</strong>: Christopher Freye (Los Alamos National Laboratory)</p><p>💾 <a target="_blank" rel="noopener noreferrer" href="https://gcms.labrulez.com/labrulez-bucket-strapi-h3hsga3/O_1_Freye_10783a9cf3.pdf"><strong>PDF presentation</strong></a></p><h3><strong>Abstract</strong></h3><p><strong>Two-dimensional gas chromatography (</strong><a target="_blank" rel="noopener noreferrer" href="https://gcms.labrulez.com/library?instrumentationItems=2"><strong>GC×GC</strong></a><strong>) when coupled with mass spectrometry (MS) especially high-resolution mass spectrometry (HRMS) provides the ideal technique to discover minute chemical changes. However, GC×GC analyses result in extremely large datasets (GBs of information) wherein the statistically significant chemical changes are buried within the background chemical matrix. To combat these issues, many chemometric techniques have been developed or applied. Recently we introduced a new chemometric technique for GC-MS termed alteration analysis (ALA) and two-dimensional correlation (2DCOR) which can be used to discover statistically significant chemical changes across a series of chromatograms and understand the relationship between the statistically relevant changes. ALA generates three sets of information, the basic alteration map (BAM) which is the magnitude of the change, the synchronous alteration map (SAM) which describes the linear change, and the asynchronous alteration map (AAM) which describes the non-linear change. 2DCOR can then be used to understand the relationship between the chemical changes but 2DCOR can also resolve the sequence of the changes. A workflow for GC×GC-MS will be demonstrated. Special attention will be given to what differentiates the GC×GC work flow from GC for both the ALA and 2DCOR.</strong></p><h3><strong>Video Transcription</strong></h3><p>The presentation focuses on how <strong>advanced mathematical and chemometric methods</strong> can be used to extract meaningful information from <strong>highly complex chromatographic data</strong>, especially in <strong>multidimensional chromatography coupled with mass spectrometry (GC×GC-MS, LC-MS)</strong>.</p><h4><strong>Why traditional data analysis falls short</strong></h4><p>Modern multidimensional chromatography generates <strong>extremely large datasets</strong>, often containing <strong>billions of data points</strong>. Visual inspection, peak tables, or classical identification-based workflows are impractical—especially when:</p><ul><li>Samples are highly complex (e.g. petroleum, metabolomics, high explosives)</li><li>Most compounds are <strong>unknown unknowns</strong></li><li>The key question is not <i>what</i> the compounds are, but <strong>whether samples differ and how</strong></li></ul><p>Program managers and decision-makers are primarily interested in <strong>detecting statistically significant changes</strong>, not exhaustive compound identification.</p><h4><strong>Introduction of Alteration Analysis (ALA)</strong></h4><p>To address subtle, trend-based changes across series of chromatograms, the speaker introduces <strong>Alteration Analysis (ALA)</strong>, a chemometric approach adapted from spectroscopy and applied to chromatography.</p><p>ALA quantitatively evaluates how <strong>individual data points change across multiple samples</strong>, allowing detection of:</p><ul><li>Extremely subtle trends</li><li>Overlapping peaks</li><li>Changes hidden in noise or baseline interference</li></ul><p>Key ALA outputs include:</p><ul><li><strong>BAM (Basic Alteration Map):</strong> magnitude of change</li><li><strong>SAM (Systematic Alteration Map):</strong> linear changes</li><li><strong>AM (Alteration Map):</strong> nonlinear changes</li></ul><p>Even changes as small as <strong>1% per sample</strong> can be detected reliably, including peaks that are heavily overlapped.</p><h4><strong>Beyond detection: understanding relationships with 2D Correlation</strong></h4><p>Once statistically significant changes are identified, <strong>two-dimensional correlation analysis (2D-COR)</strong> is used to understand <strong>relationships between changing compounds</strong>, including:</p><ul><li>Whether compounds are correlated or anti-correlated</li><li>The <strong>sequence of changes over time</strong> (which changes happen first)</li></ul><p>This is especially critical for <strong>degradation and aging studies</strong>, where intermediate species may appear and disappear before the final state—information that traditional methods like Fisher ratio or PCA often miss.</p><h4><strong>Solving GC×GC challenges with tiling</strong></h4><p>GC×GC data introduces additional challenges due to:</p><ul><li>Peak misalignment</li><li>Exponential data growth during correlation calculations</li></ul><p>The presenter explains how <strong>tile-based approaches</strong> reduce data dimensionality, overcome alignment issues, and make ALA and 2D correlation computationally feasible—even for massive GC×GC-MS datasets.</p><h4><strong>Real-world application: explosive aging studies</strong></h4><p>The methodology was applied to <strong>aging and decomposition of high explosives</strong>, where:</p><ul><li>Over <strong>250 chemical changes</strong> were identified</li><li>Many intermediate species would have been missed using traditional comparisons</li><li>ALA combined with 2D correlation enabled reconstruction of <strong>degradation pathways</strong></li><li>The most significant change was <strong>not necessarily the first change</strong>, a critical insight for risk assessment and stability studies</li></ul><h4><strong>Key takeaway</strong></h4><p>By combining <strong>Alteration Analysis and 2D correlation</strong>, the approach:</p><ul><li>Detects statistically guaranteed chemical changes</li><li>Handles subtle, overlapped, and noisy signals</li><li>Determines <strong>magnitude, type, interrelationships, and order of changes</strong></li><li>Shifts chromatographic data analysis from identification-driven to <strong>decision-driven</strong></li></ul><p>This math-driven workflow enables faster, more reliable interpretation of complex chromatographic datasets and provides actionable insights for applications such as <strong>explosive aging, pharmaceutical degradation, and complex mixture analysis</strong>.</p><blockquote><p><strong>This text has been automatically transcribed from a video presentation using AI technology. It may contain inaccuracies and is not guaranteed to be 100% correct.</strong></p></blockquote>

Discovery analysis for GCxGC trends using alteration and 2D correlation (Chris Freye, MDCW 2026)

<p><strong>Our Library never stops expanding. What are the most recent contributions to LabRulezGCMS Library in the week of 9th February 2026? Check out new documents from the field of the gas phase, especially GC and GC/MS techniques!</strong></p><blockquote><p><span style="font-size:20px;">👉 </span><a target="_blank" rel="noopener noreferrer" href="https://gcms.labrulez.com/library"><span style="font-size:20px;"><strong>SEARCH THE LARGEST REPOSITORY OF DOCUMENTS ABOUT GCMS AND RELATED TECHNIQUES</strong></span></a></p></blockquote><blockquote><p><strong>👉 Need info about different analytical techniques?</strong> Peek into <a target="_blank" rel="noopener noreferrer" href="https://lcms.labrulez.com/library"><strong>LabRulezLCMS</strong></a> or <a target="_blank" rel="noopener noreferrer" href="https://icpms.labrulez.com/library"><strong>LabRulezICPMS</strong></a> libraries.</p></blockquote><p>This week we bring you technical note by <strong>Agilent Technologies, </strong>presentation by<strong> MDCW / University of Copenhagen </strong>and<strong> </strong>application notes by<strong> Shimadzu </strong>and<strong> Thermo Fisher Scientific!</strong></p><h3><strong>1. Agilent Technologies: What Causes Spots on </strong><a target="_blank" rel="noopener noreferrer" href="https://gcms.labrulez.com/library?instrumentationItems=19&amp;manufacturerItems=1&amp;search=PLOT"><strong>PLOT Columns</strong></a><strong>? Will It Affect the Performance of the Column?</strong></h3><ul><li>Technical note</li><li><a target="_blank" rel="noopener noreferrer" href="https://gcms.labrulez.com/labrulez-bucket-strapi-h3hsga3/te_what_causes_spots_plot_columns_affecting_performance_5994_8775en_agilent_3b7180512a.pdf"><strong>Full PDF for download</strong></a></li></ul><p>Spots on porous layer open tubular (PLOT) columns are caused by small voids in the stationary phase coating inside the tube. These spots are areas where there is an uneven coating or lack of phase. It is normal to find some voids in the phase coating of PLOT columns. The stationary phase in PLOT columns is an opaque, solid, and porous material. In many Agilent PLOT columns such as the GS-Alumina phases, molecular sieves, porous polymers (Q and U), and the GS-OxyPLOT, the stationary phase is visible as a white powder. For many PLOT columns, the stationary phase fill solution is a viscous suspension of particles that are less than 10 microns in diameter. The phase is coated using a dynamic process in which a plug of fill solution is pushed through the tubing, and the plug’s speed and viscosity determines the thickness of the stationary phase layer. Once the PLOT’s stationary phase is deposited, it is held in place by electrostatic charge, chemical interactions between particles, and/or binding agents. In wall‑coated open tubular (WCOT) columns, stationary phases such as polysiloxanes or polyethylene glycols are immobilized by chemical bonding to the glass surface and cross-linking between polymer strands. Because this type of bonding and cross‑linking is not possible with PLOT phases, the result is a stationary phase layer that is both fundamentally different and inherently less stable in PLOT columns than in WCOT&nbsp;columns.</p><h3><strong>2. MDCW / University of Copenhagen: One-shot tensor decomposition of full-scale GC×GC-VUV datasets for resolving petrochemical groups</strong></h3><ul><li>Presentation</li><li><a target="_blank" rel="noopener noreferrer" href="https://gcms.labrulez.com/labrulez-bucket-strapi-h3hsga3/O_17_Schneide_67c8ff7866.pdf"><strong>Full PDF for download</strong></a></li></ul><p>The presentation introduces a novel <strong>all-samples-at-once, shift-invariant tri-linear tensor decomposition approach</strong> for the analysis of full-scale <a target="_blank" rel="noopener noreferrer" href="https://gcms.labrulez.com/library?search=GC%C3%97GC-VUV"><strong>GC×GC-VUV</strong></a><strong> datasets</strong>, aimed at resolving and quantifying petrochemical groups. Traditional template-based or pixel-based methods struggle with retention-time shifts and co-eluting compounds, often requiring manual intervention and prior chemical knowledge. The proposed approach leverages the intrinsic low-rank structure of GC×GC-VUV data to enable robust, automated group-level analysis across multiple samples simultaneously.</p><p>At the core of the method is a <strong>shift-invariant tri-linear model</strong>, conceptually related to PARAFAC and multivariate curve resolution, but extended using frequency-domain (FFT-based) modeling to explicitly account for chromatographic peak shifts. By decomposing the entire dataset in one step, the model provides <strong>accurate estimates of peak landscapes, VUV spectra, and relative peak areas</strong>, while remaining agnostic to retention-time variability. Importantly, the approach requires only a small number of tunable parameters, making it practical for routine use.</p><p>The method was demonstrated on a <strong>case study involving 14 petrochemical gas-oil samples</strong>, including straight-run, hydrotreated, hydroconverted, coker, and light cycle oils. Extracted VUV spectra showed excellent agreement with reference spectra from a VUV spectral database, enabling confident assignment of components to chemical groups such as saturates, olefins, and mono- to poly-aromatics. Quantitative results exhibited <strong>high repeatability (RSD typically 3–9%)</strong> and strong correlation with established template-based reference methods.</p><p>Overall, the work demonstrates that <strong>one-shot, shift-invariant tensor decomposition</strong> provides a powerful and scalable alternative to conventional GC×GC data-analysis strategies. By combining chemical interpretability, robustness to chromatographic shifts, and strong quantitative performance, the approach opens new opportunities for automated, high-confidence group-level analysis of complex petrochemical samples and beyond.</p><h3><strong>3. Shimadzu: Py-Screener Ver. 3: Simultaneously Test for Substances Regulated Under RoHS, TSCA, and POPs</strong></h3><ul><li>Application note</li><li><a target="_blank" rel="noopener noreferrer" href="https://gcms.labrulez.com/labrulez-bucket-strapi-h3hsga3/an_01_00949_en_4754e50164.pdf"><strong>Full PDF for download</strong></a></li></ul><h5><strong>User Benefits</strong></h5><ul><li>In just one analysis, <a target="_blank" rel="noopener noreferrer" href="https://gcms.labrulez.com/library?manufacturerItems=3&amp;search=Py-Screener"><strong>Py-Screener</strong></a> Ver. 3 can determine levels of phthalate esters, brominated flame retardants (PBBs, PBDEs), PIP (3:1), UV-328, dechlorane plus (DP), short-chain chlorinated paraffins (SCCPs), and medium-chain chlorinated paraffins (MCCPs).&nbsp;</li><li>It can also test for SCCPs and MCCPs by electron ionization (EI) instead of negative chemical ionization (NCI).&nbsp;</li><li>PIP (3:1), UV-328, DP, and SCCPs and MCCPs can be screened without the need for corresponding reference materials.</li></ul><p>Countries and regulatory bodies worldwide are introducing increasingly stringent regulations on the chemical substances used in electronic devices and industrial products. The RoHS Directive and REACH regulations in the EU, the Toxic Substances Control Act (TSCA) in the USA, and the Stockholm Convention on Persistent Organic Pollutants (POPs) are also targeting an increasingly broad range of substances. Therefore, manufacturers are required to accurately identify regulated substances in their products and comply with each regulation. While Py-Screener Ver. 2 can screen for seven phthalate esters and brominated flame retardants, including substances regulated under the RoHS Directive, version 3 can also screen for PIP (3:1), which is regulated under the TSCA, as well as UV328, DP, and SCCPs and MCCPs , which are regulated under the Stockholm Convention on POPs. A list of supported substances isshown in Table 1. This article introduces the simultaneous analysis of multiple regulated substances and a case study of testing specific regulated substances in samples, using Py-Screener Ver. 3.</p><h4><strong>Analysis Process</strong></h4><p>Py-Screener Ver. 3 can determine levels of phthalate esters and brominated flame retardants contained in products in accordance with the international analytical standards IEC62321-8 and IEC62321-3-3. It can also test for specific regulated substances (Table 1) under the same conditions and in the same analysis. In this test, background intensity and instrument sensitivity (S/N) were verified before analyzing samples. These parameters are prescribed by IEC62321-8 to ensure the accuracy of the methods used. Background intensity and instrument sensitivity were determined using a reference material (PN: 225-31003- 91) *1 that consisted of a plastic sheet that was spiked with seven phthalate esters. The results met the criteria for both parameters.</p><p>The testing workflow is shown in Fig. 1. Before testing samples, calibration curves were prepared by analyzing the 1000 mg/kg phthalate ester reference material and polypropylene spiked with brominated flame retardants (ERM-EC591). A hole puncher was used to punch out two discs at a time of the phthalate ester reference material, and a cutter was used to obtain pieces of the other materials. Each material was weighed in a sample cup for analysis. During the analysis of samples, phthalate esters and some of the regulated brominated flame retardants were quantitated using a one-point calibration curve. The remaining brominated flame retardants and specific regulated substances were quantitated using the correction factor database*2 that is included with Py-Screener Ver. 3.</p><h4><strong>Conclusion</strong></h4><p>Py-Screener Ver. 3 successfully determined in samples the concentrations of the regulated substances PIP (3:1), UV-328, DP, and SCCPs and MCCPs. Normally, SCCP and MCCP levels are tested using NCI, but Py-Screener Ver. 3 uses EI. This enables it to test for not only SCCPs and MCCPs but also phthalate esters, brominated flame retardants, and other regulated substances in just one analysis. In addition, by using the relative correction factors linked to DEHP in the phthalate ester reference material, the levels of these regulated substances were determined without the need for the corresponding reference materials. Py-Screener Ver. 3 can also create a screening program that addresses substance restrictions under the RoHS Directive, the US TSCA, and the POPs Convention.</p><h3><strong>4. Thermo Fisher Scientific: Improving low carbon steel production in specialty steel processes</strong></h3><ul><li>Application note</li><li><a target="_blank" rel="noopener noreferrer" href="https://gcms.labrulez.com/labrulez-bucket-strapi-h3hsga3/prima_pro_process_mass_spectrometer_an1626_7fc840235f.pdf"><strong>Full PDF for download</strong></a></li></ul><p>World crude steel production reached 1,691 million tonnes in 2017, up by 5.3% compared to 2016.1 While much of this capacity is still produced in primary steel processes such as basic oxygen furnaces and electric arc furnaces, the need for refined steel with greater durability and resistance to heat and corrosion has led to the increased use of vacuum degassing processes, such as VOD and RH, in secondary steel production. These processes are able to achieve ultra-low levels of residual carbon, while at the same time retaining desired levels of other alloy materials. If these processes are to achieve the required level of steel product quality, they need fast, continuous gas analysis of the furnace exhaust gas. Without accurate information on the composition of the gas leaving the furnace, any variations in the decarburization process are only detected after the event, resulting in the production of out-of-specification steel.</p><h4><strong>Advantages of mass spectrometry&nbsp;</strong></h4><p>Traditional Non-Dispersive Infra-Red (NDIR) analyzers are used in many conventional steelmaking processes to measure CO and CO<sub>2</sub> , but they can only sample at atmospheric pressure. In vacuum steelmaking the process pressure changes dramatically, typically from atmospheric pressure down to less than 1 mbar, over the 20-30 minutes of the melt. So NDIR analyzers have to sample some distance downstream from the process. Analytical data is updated several minutes after the gas leaves the melt and the control system is forced to operate on historic rather than real-time data.&nbsp;</p><p>Paramagnetic analyzers can be used to measure O<sub>2</sub> , while thermal conductivity analyzers can be used to measure H<sub>2</sub> . These analyzers also suffer from slow response, while the need to operate three different types of analyzers adds to the plant maintenance burden. Moreover, the three analyzers cannot analyze inert gases, so N<sub>2</sub> is calculated by difference, a result that suffers from the sum of the errors of the three analytical techniques.&nbsp;</p><p>Mass spectrometry operates at high vacuum so it is ideal for monitoring vacuum processes. It is also able to monitor all seven components in Table 1 in seconds rather than minutes, ensuring the plant control model is frequently updated with accurate compositional data.</p><h4><strong>Precision of analysis&nbsp;</strong></h4><p>At the heart of the <a target="_blank" rel="noopener noreferrer" href="https://gcms.labrulez.com/library?manufacturerItems=2&amp;search=Prima+PRO+Mass+Spectrometer"><strong>Thermo Scientific™ Prima PRO Mass Spectrometer</strong></a> (MS) is a magnetic sector analyzer which offers unrivalled precision and accuracy compared with other mass spectrometers. Thermo Fisher Scientific manufactures both quadrupole and magnetic sector mass spectrometers; over thirty years of industrial experience have shown the magnetic sector based analyzer offers the best performance for industrial on-line gas analysis.&nbsp;</p><p>Key advantages of magnetic sector analyzers include improved precision, accuracy, long intervals between calibrations, and resistance to contamination. Typically, analytical precision is between 2 and 10 times better than a quadrupole analyzer, depending on the gases analyzed and complexity of the mixture.&nbsp;</p><p>A unique feature of the Prima PRO magnet is that it is laminated. Its analysis times are similar to a quadrupole analyzer, offering the unique combination of rapid analysis and high stability. This allows the rapid and extremely stable analysis of an unlimited number of user-defined gases. The scanning magnetic sector is controlled with 24-bit precision using a magnetic flux measuring device for extremely stable mass alignment.&nbsp;</p><p>The ion source is an enclosed type for high sensitivity, minimum background interference, and maximum contamination resistance. This is a high-energy (1000 eV) analyzer that offers extremely rugged performance in the presence of gases and vapors that have the potential for contaminating the analyzer. Typical performance specifications for the Prima PRO MS are shown in Table 1. Analytical performance is demonstrated by analyzing the calibration bottle over 1 hour following calibration, with an analysis time of just 6 seconds. Standard deviations measured on the calibration cylinder will be equal to or better than the stated values.</p>

News from LabRulezGCMS Library - Week 07, 2026

Article

Application

Academy

Video

Presentation

The Multidimensional Chromatography (MDC) Workshop draws experts in this exciting field to share and discuss their research.

The Multidimensional Chromatography Workshop

Everything from the world of analytical chemistry in one place. We connect people in solving their problems. At Labrulez you will find all the necessary information easily, quickly and clearly. Stop searching and start finding.

LabRulez

Phenomenex is a global technology leader committed to developing novel analytical chemistry solutions that solve the separation and purification challenges of researchers in industrial, government and academic laboratories.

Phenomenex

Thermo Scientific™ Q Exactive™ GC Orbitrap GC-MS/MS System

High-resolution GC-MS system combining Orbitrap accuracy with full-scan sensitivity and MS/MS power for confident quantitation and compound identification in complex matrices.

<h4><strong>Next-generation high-resolution GC-MS for confident quantitation and unknown identification</strong></h4><p>The <strong>Q Exactive GC Orbitrap GC-MS/MS system</strong> is the first commercial benchtop system to combine <strong>gas chromatography with Orbitrap™ high-resolution accurate-mass (HRAM) detection</strong>. It offers unrivaled resolving power, sub-ppm mass accuracy, and the quantitation power of triple quadrupole systems — all in untargeted full-scan mode.</p><p>Designed for <strong>food safety, metabolomics, environmental, clinical, and pharmaceutical labs</strong>, this hybrid quadrupole-Orbitrap system brings unmatched performance for both discovery and targeted workflows, with robust EI/CI ionization, smart deconvolution, and intuitive software.</p><h3><strong>Key Benefits</strong></h3><h4>🎯 <strong>High-resolution power for confident detection</strong></h4><ul><li>Up to <strong>100,000 resolution (FWHM)</strong> at m/z 272</li><li><strong>Sub-1 ppm mass accuracy</strong> (internal) in routine full-scan MS</li><li>Accurate detection even in <strong>part-per-trillion</strong> range</li><li>Resolves coeluting peaks in complex matrices with ease</li></ul><h4>💡 <strong>Unmatched qualitative and quantitative versatility</strong></h4><ul><li>EI, PCI, NCI ionization with <strong>ExtractaBrite™ source</strong> (removable under vacuum)</li><li><strong>Full-scan sensitivity equal to SRM</strong> mode of triple quadrupoles</li><li>PRM and MS/MS with <strong>HCD collision cell</strong></li><li><strong>Variable electron voltage (VeV)</strong> for softer EI and improved identification</li></ul><h4>🧠 <strong>Advanced tools for unknown identification</strong></h4><ul><li><strong>Deconvolution software</strong> with HRAM fragment interpretation</li><li>Compatibility with NIST/Wiley libraries and <strong>HRAM spectral libraries</strong></li><li>Supports <a target="_blank" rel="noopener noreferrer" href="https://gcms.labrulez.com/products/77"><strong>TraceFinder™</strong></a>, <a target="_blank" rel="noopener noreferrer" href="https://gcms.labrulez.com/products/1759"><strong>Compound Discoverer™</strong></a>, and<a target="_blank" rel="noopener noreferrer" href="https://lcms.labrulez.com/products/1757"> <strong>Mass Frontier™</strong></a></li></ul><h3><strong>System Capabilities</strong></h3><ul><li><strong>Mass range</strong>: 30–3000 m/z</li><li><strong>Mass accuracy</strong>: &lt;1 ppm RMS (internal), &lt;3 ppm RMS (external)</li><li><strong>Quantitative dynamic range</strong>: &gt;10⁶</li><li><strong>In-spectrum dynamic range</strong>: &gt;5000:1</li><li><strong>Scan speed</strong>: up to 18 Hz @ 12,500 resolution</li><li><strong>Simultaneous detection</strong> of up to 10 precursors per scan</li></ul><h3><strong>Operation &amp; Workflow</strong></h3><ul><li><strong>Full MS</strong>, <strong>SIM</strong>, <strong>Timed SIM</strong>, <strong>PRM</strong>, polarity switching, DDA</li><li><strong>Automatic gain control (AGC)</strong> ensures optimal ion population in Orbitrap</li><li>Easy maintenance with <strong>vent-free source and column exchange</strong></li><li>Seamless <a target="_blank" rel="noopener noreferrer" href="https://lcms.labrulez.com/products/1758"><strong>Xcalibur™</strong></a> and <a target="_blank" rel="noopener noreferrer" href="https://gcms.labrulez.com/products/77"><strong>TraceFinder™</strong></a> control with automated tuning/calibration</li></ul><h3><strong>Sample Introduction &amp; Automation</strong></h3><ul><li>Compatible with <strong>TRACE™ 1310 GC</strong> with Instant Connect injectors</li><li>Autosamplers: <strong>TriPlus RSH</strong> for full automation and microsample workflows</li><li>Direct probes (DEP/DIP) for solid/liquid samples — no venting required</li></ul><h3><strong>Applications</strong></h3><ul><li>Food safety &amp; authenticity (pesticides, packaging migration)</li><li>Metabolomics, environmental &amp; clinical toxicology</li><li>Extractables &amp; leachables, forensics, pharmaceuticals</li><li>Untargeted and targeted multi-analyte screening</li></ul><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/application::product.product/QExactive-GCMSMS-Orbitrap-with-Autosampler-Front-1858x1391.jpg-650.jpg" alt="Thermo Scientific™ Q Exactive™ GC Orbitrap GC-MS/MS System" width="null" height="null"></p>

Thermo Scientific™ Exactive™ GC Orbitrap™ GC-MS System

High-resolution Orbitrap GC-MS system for confident quantitation and unknown screening. Delivers sub-ppb sensitivity, <1 ppm accuracy, and routine full-scan workflows.

<h4><strong>Bringing high-resolution Orbitrap technology into routine GC-MS workflows</strong></h4><p><strong>The Exactive GC Orbitrap system offers the unmatched mass accuracy, resolving power, and sensitivity of Orbitrap technology in a platform optimized for routine applications. This high-performance GC-MS system enables both targeted and non-targeted full-scan workflows with confident quantitation and trace-level detection, even in complex matrices. Designed for maximum robustness and usability, it streamlines operations across food safety, environmental, industrial, forensic, and anti-doping laboratories.</strong></p><h3><strong>Key Features and Benefits</strong></h3><h4>💡 <strong>Unmatched HRAM Performance</strong></h4><ul><li>Resolving power up to <strong>60,000 FWHM at m/z 200</strong></li><li>Mass accuracy: <strong>&lt;1 ppm</strong> (internal), <strong>&lt;3 ppm</strong> (external)</li><li>Quantitative dynamic range: <strong>&gt;10⁶</strong>, with excellent linearity and precision</li><li>Routine IDLs in the <strong>sub-ppb to ppt range</strong></li></ul><h4>🧪 <strong>Full-Scan Sensitivity and Selectivity</strong></h4><ul><li>Combines triple-quad-like quantitation with full-scan Orbitrap capability</li><li>Sub-ppb sensitivity for 100+ pesticides in food matrices</li><li>High selectivity and confidence in trace-level compound identification</li><li>Spectral deconvolution with accurate-mass fragment filtering</li></ul><h4>⚙️ <strong>Proven Orbitrap Design</strong></h4><ul><li>Curved linear trap (C-Trap) and bent flatapole ion optics</li><li>ExtractaBrite™ ion source (EI/PCI/NCI) – removable under vacuum</li><li>Vent-free column exchange using patented source plug</li><li>Optional direct sample probes (DIP, DEP) for solid or thermolabile analytes</li></ul><h4>🧠 <strong>Streamlined Software and Data Processing</strong></h4><ul><li>Controlled by <a target="_blank" rel="noopener noreferrer" href="https://gcms.labrulez.com/products/77"><strong>TraceFinder™</strong></a> and <a target="_blank" rel="noopener noreferrer" href="https://lcms.labrulez.com/products/1758"><strong>Xcalibur™</strong></a> platforms</li><li>Full-scan acquisition with automated data mining</li><li>Integrated spectral libraries (NIST, Thermo Food/Environmental)</li><li>Spectral fidelity and mass accuracy retained across wide concentration range</li></ul><h4>🔁 <strong>Optimized GC Integration</strong></h4><ul><li>Built on the <strong>TRACE™ 1310 GC platform</strong></li><li>Supports all injection/detection configurations (SSL, PTV, backflush, etc.)</li><li>Paired with <strong>TriPlus™ RSH autosampler</strong> for advanced robotic sample handling</li><li>Excellent retention time stability and fast oven cycling</li></ul><h3><strong>Ideal For Applications In:</strong></h3><ul><li><strong>Food safety and authenticity</strong> (pesticide screening, additives)</li><li><strong>Environmental analysis</strong> (contaminants, pollutants, air toxics)</li><li><strong>Forensics and toxicology</strong> (unknowns, drugs, metabolites)</li><li><strong>Industrial QC</strong> (extractables, volatiles, impurity profiling)</li><li><strong>Non-targeted screening</strong> with full-scan HRAM and retrospective analysis</li></ul><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/application::product.product/exactive-gc-orbitrap-gc-ms-front-2000x2000.jpg-650.jpg" alt="Thermo Scientific™ Exactive™ GC Orbitrap™ GC-MS System" width="null" height="null"></p>

Thermo Scientific™ ISQ™ 7000 Single Quadrupole GC-MS System

Robust single quad GC-MS with advanced ion sources, NeverVent™ tech, SmartTune, and flexible software. Delivers sensitive, high-throughput routine analysis.

<h4><strong>Unstoppable GC-MS performance for routine, regulatory, and high-throughput analysis</strong></h4><p><strong>The ISQ 7000 GC-MS system delivers reliable, scalable, and ultra-sensitive performance for routine analysis in food safety, environmental, clinical, and forensic laboratories. Designed to maximize uptime and analytical confidence, it features advanced ion source options, easy maintenance with NeverVent™ technology, and intuitive software tools like SmartTune and AutoSIM.</strong></p><h3><strong>Key Features and Benefits</strong></h3><h4>🚀 <strong>Unstoppable Sensitivity</strong></h4><ul><li>Advanced Electron Ionization (AEI) source for femtogram-level detection</li><li>Robust ExtractaBrite™ ion source, fully removable under vacuum</li><li>Dual-filament design and S-shaped ion optics reduce neutral and chemical noise</li><li>Simultaneous full-scan and SIM acquisition modes</li></ul><h4>⚙️ <strong>Unstoppable Uptime</strong></h4><ul><li><strong>NeverVent™ technology</strong> with Vacuum Probe Interlock (VPI) and V-Lock for maintenance without venting</li><li>Heated ion optics and RF lens protect quadrupole from matrix contamination</li><li>Reliable quadrupole design: solid, non-coated rods and maintenance-free performance</li><li>Up to <strong>98% downtime reduction</strong> for routine interventions (e.g. source cleaning)</li></ul><h4>🧠 <strong>Smart Automation and Ease of Use</strong></h4><ul><li><strong>SmartTune</strong> for guided, fast, and consistent system tuning</li><li><strong>AutoSIM</strong> and <strong>Timed-SIM (t-SIM)</strong> for efficient method creation</li><li><strong>Retention Time Alignment (RTA)</strong> tool for consistent results across column changes</li><li>Deconvolution tools for untargeted compound identification</li></ul><h4>🧪 <strong>Flexible Analytical Capabilities</strong></h4><ul><li>EI, PCI, NCI ionization modes (with optional dual reagent gas switching)</li><li>Mass range: 1.2–1100 u; scanning speed up to 240 scans/s</li><li>Optional Direct Insertion and Direct Exposure probes for solid samples</li><li>Software-switchable ionization modes in a single analysis</li></ul><h4>🖥️ <strong>Integrated Software and Data Handling</strong></h4><ul><li>Full control via <a target="_blank" rel="noopener noreferrer" href="https://gcms.labrulez.com/products/76"><strong>Chromeleon™ CDS</strong></a> or <a target="_blank" rel="noopener noreferrer" href="https://gcms.labrulez.com/products/77"><strong>TraceFinder™</strong></a></li><li>Preloaded application libraries and eWorkflows (e.g. US EPA, clinical, toxicology)</li><li>Auto-calibration, QA/QC tools, and compliance-ready (21 CFR Part 11)</li><li>Seamless LIMS connectivity and user-guided reporting tools</li></ul><h4>🔁 <strong>Sample Introduction Options</strong></h4><ul><li>Compatible with <strong>AI/AS 1310</strong>, <strong>TriPlus 300</strong> (HS), and <strong>TriPlus RSH</strong> autosamplers</li><li>Robotic workflows including dilution, standard addition, and derivatization</li><li>Ideal for trace analysis in complex matrices and high-throughput environments</li></ul><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/application::product.product/isq-7000-trace-1310-triplus-rsh-left-1200x1200.jpg-650_s.webp" alt="Thermo Scientific™ ISQ™ 7000 Single Quadrupole GC-MS System" width="382" height="382"></p>

Thermo Scientific™ TRACE™ 1310 Gas Chromatograph

Modular GC with touch screen control, instant-connect injectors, helium-saving capability, and fast oven cycles—ideal for method development and routine analysis.

<h4><strong>Premium modular GC system with full local control for method development and routine analysis</strong></h4><p><strong>The TRACE 1310 GC combines the modular, tool-free architecture of the TRACE 1300 Series with a powerful built-in user interface for complete instrument control. Designed for analysts who demand flexibility, speed, and intuitive access to GC parameters, the system supports all injection and detection configurations and delivers exceptional performance for both routine QA/QC and advanced method development.</strong></p><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/application::product.product/Thermo-Trace-1310-GC-System-1.jpg" alt="Thermo Scientific™ TRACE™ 1310 Gas Chromatograph" width="null" height="null"></p><h3><strong>Key Features and Benefits</strong></h3><h4>🖥️ <strong>Full Local Control</strong></h4><ul><li>Integrated <strong>touch screen interface</strong> for real-time method setup and control</li><li>Intuitive navigation for injector, detector, oven, and flow parameters</li><li>Ideal for <strong>method development</strong> and <strong>standalone operation</strong> without PC</li></ul><h4>⚙️ <strong>Modular Instant Connect Design</strong></h4><ul><li>Exchange injectors and detectors in under 2 minutes</li><li>Tool-free reconfiguration without downtime</li><li>Compatible with all TRACE 1300 modules and autosamplers</li></ul><h4>💨 <strong>Fast and Stable Thermal Performance</strong></h4><ul><li>Oven ramp rate up to <strong>125 °C/min</strong>, cool-down in under 4 minutes</li><li>Excellent retention time and area reproducibility</li><li>Cryogenic cooling available down to –100 °C</li></ul><h4>♻️ <strong>Helium Saver Ready</strong></h4><ul><li>Use helium, hydrogen, or nitrogen as carrier gases</li><li>Reduce helium consumption by over 90%</li><li>Maintain method integrity while switching gases</li></ul><h4>🧪 <strong>Broad Application Coverage</strong></h4><ul><li>Supports SSL, PTV, On-Column, Large Volume Injection, Backflush</li><li>Detector options: FID, TCD, ECD, NPD, FPD, MS interface</li><li>Compatible with manual or automated workflows (AI/AS 1310, TriPlus RSH)</li></ul><h3><strong>Software and Integration</strong></h3><ul><li>Fully controllable via <a target="_blank" rel="noopener noreferrer" href="https://gcms.labrulez.com/products/76"><strong>Chromeleon™</strong></a><strong>, </strong><a target="_blank" rel="noopener noreferrer" href="https://lcms.labrulez.com/products/1758"><strong>Xcalibur™</strong></a><strong>, or Chrom-Card™</strong></li><li>eWorkflows for simplified operation and data processing</li><li>Built-in QC, audit trail, and LIMS compatibility</li></ul><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/application::product.product/Thermo-TriPlus-500-GC-Headspace-Autosampler-3.jpg" alt="Thermo Scientific™ TRACE™ 1310 Gas Chromatograph" width="null" height="null"></p>

Thermo Scientific™ TSQ™ 9000 GC-MS/MS System

Triple quadrupole GC-MS/MS system offering exceptional sensitivity, robustness, and smart automation for trace-level quantitation in food, environmental, and forensic analysis.

<p><strong>High-performance triple quadrupole GC-MS/MS platform for routine trace-level quantitation in complex matrices</strong></p><p>The <strong>TSQ™ 9000 GC-MS/MS system</strong> is built for laboratories that demand <strong>uncompromising sensitivity, throughput, and robustness</strong> for trace-level analysis in <strong>food safety, environmental, and forensic/toxicology applications</strong>. Designed to increase productivity and reduce cost-per-sample, this system delivers best-in-class performance with intuitive tools for routine and advanced users alike.</p><h3><strong>Key features and benefits</strong></h3><h4>🚀 <strong>Unstoppable Sensitivity</strong></h4><ul><li><strong>Advanced Electron Ionization (AEI)</strong> source for attogram-level sensitivity, ideal for demanding applications like dioxins and pesticides in baby food.</li><li><strong>ExtractaBrite™ ion source</strong>: robust EI/CI performance, proven in routine use; fully removable under vacuum with NeverVent™.</li><li><strong>Ionization modes: </strong>EI, PCI, NCI (CI available with ExtractaBrite only)</li></ul><h4>🔬 <strong>Unstoppable Performance</strong></h4><ul><li><strong>EvoCell™ collision cell</strong>: up to 800 SRM transitions/s with excellent precision</li><li><strong>0.5 ms minimum dwell time</strong>; up to 97 scans/s; 20,000 u/s quadrupole scan speed</li><li><strong>Mass range</strong>: 1.2–1100 u, unit mass resolution</li><li><strong>Mass stability</strong>: &lt;0.1 u over 48 h</li></ul><h4>🔧 <strong>Unstoppable Uptime</strong></h4><ul><li><strong>NeverVent™ technology</strong> (with VPI &amp; ExtractaBrite): perform maintenance or column changes without venting</li><li><strong>V-Lock</strong> column isolation prevents system venting during GC maintenance</li><li><strong>Dual heated source lenses</strong> for minimal contamination and high matrix tolerance</li></ul><h3><strong>Ease of Use and Intelligent Method Development</strong></h3><ul><li><strong>AutoSRM™</strong>: Automated SRM development wizard</li><li><strong>SIM Bridge™</strong>: Convert legacy SIM methods into SRM in seconds</li><li><strong>Timed-SRM and Retention Time Alignment (RTA)</strong>: Maintain optimal sensitivity and peak tracking across injections</li><li><strong>SmartTune™</strong>: Intuitive system tuning with error guidance</li></ul><h3><strong>Software Platforms</strong></h3><h4><a target="_blank" rel="noopener noreferrer" href="https://lcms.labrulez.com/products/76"><strong>Chromeleon™ CDS</strong></a></h4><ul><li>Fully integrated control of chromatography and mass spectrometry</li><li>One-click eWorkflows™, Intelligent Run Control, automated compliance tools</li><li>Environmental Analysis Extension Pack for U.S. EPA workflows</li></ul><h4><a target="_blank" rel="noopener noreferrer" href="https://lcms.labrulez.com/products/77"><strong>TraceFinder™</strong></a></h4><ul><li>Comprehensive solution for method development, acquisition, processing, and reporting</li><li>Preloaded SRM database for over 1300 pesticides (environmental/food safety versions)</li><li>Application-specific variants for <strong>clinical research</strong>, <strong>toxicology</strong>, and <strong>environmental labs</strong></li></ul><h3><strong>System Specifications</strong></h3><ul><li><strong>Ion sources</strong>: AEI and ExtractaBrite (CI optional)</li><li><strong>Transfer line temperature</strong>: up to 400 °C</li><li><strong>Detector</strong>: DynaMax™ XR system with off-axis dynode and wide dynamic range (&gt;10⁷)</li><li><strong>Mass resolution</strong>: Adjustable 0.4–2.5 u, preset or manual</li><li><strong>Pumping system</strong>: High-capacity turbomolecular with rotary vane or optional oil-free scroll</li><li><strong>Direct Probe Options (VPI only)</strong>: DIP and DEP probes for solid and rapid samples</li></ul><h3><strong>Sample Introduction Options</strong></h3><ul><li><a target="_blank" rel="noopener noreferrer" href="https://gcms.labrulez.com/products/68"><strong>AI/AS 1310 Autosampler</strong></a>: high-precision injections, advanced rinse protocols</li><li><strong>TriPlus™ RSH Autosampler</strong>: robotic automation including dilution, internal standard addition, derivatization, and tool switching</li></ul><h3><strong>System Dimensions and Compatibility</strong></h3><ul><li>Fully compatible with <strong>Thermo Scientific™ TRACE™ 1300/1310 GC</strong></li><li><strong>Mass spectrometer</strong>: 44 × 40 × 89 cm; 61 kg</li><li>Modular design enables scalable performance and easy upgrades</li></ul><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/application::product.product/Thermo-TSQtm-9000-1310-triplus-rsh_l.webp" alt="Thermo Scientific™ TSQ™ 9000 GC-MS/MS System" width="708" height="708"></p>

Thermo Scientific AI/AS 1310 liquid sampling automation

The AI/AS 1310 autosampler series offers 8 to 155-position capacity for GC liquid injections, combining robustness and ease of use for both QA/QC and high-throughput labs.

<p><strong>As the next evolution in sampling automation, the Thermo Scientific™ AI/AS 1310 Series autosampler is the optimum choice for gas chromatography liquid injections. Ranging from an 8-position system (AI 1310 Autoinjector) to a 155 sample capacity autosampler (AS 1310), these systems are engineered to meet the highest requirements of ruggedness and ease of use and fulfill the needs of both QA/QC and high-throughput environments.</strong></p><h4><strong>Syringe thermal stability</strong></h4><p>The syringe is kept away from the inlet’s temperature influence so that efficient sampling of low boiling compounds is preserved.</p><h4><strong>Cross-contamination free</strong></h4><p>Pre- and Post-injection syringe rinsing with single or combined solvents (A, B, C, D, A+B, C+D) makes carry-over negligible.</p><h4><strong>System upgradability</strong></h4><p>An upgrade option is available for AI 1310 to extend its sample throughput to the 155 sample capacity of the AS 1310 autosampler.</p><h4><strong>System control</strong></h4><p>All necessary electronics are on board the sampling module. Both AI 1310 and AS 1310 can be controlled through the data system set-up menu.</p><h4><strong>System setup</strong></h4><p>Easy self-aligning, slide-in installation does not require any turret/syringe adjustment over the injector or the sample vial.</p><h4><strong>RoHS compliance</strong></h4><p>The AI/AS 1310 is compliant with the latest Restriction of Hazardous Substances (RoHS) requirements for hazardous substances in electrical and electronic equipment.</p><h4><strong>Removable trays</strong></h4><ul><li><strong>AI 1310 - The 8-position sample holder </strong>can easily be removed and replaced by another one. Each sample holder can be specifically labeled and used for sample preparation or storing.</li><li><strong>AS 1310 - The 155-position rotating carousel</strong> can be easily removed and replaced for sample preparation or storage if required.</li></ul><h4><strong>AS 1310 Gemini kit</strong></h4><p>Simply and easily automate simultaneous injections on two channels on the Thermo Scientific gas chromatographs, for double the productivity.</p><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/application::product.product/Thermo-Trace-1310-GC-System-1.jpg" alt="Thermo Scientific AI/AS 1310 liquid sampling automation" width="null" height="null"></p><h3><strong>System specifications</strong></h3><h4><strong>Sample loading capacity</strong></h4><ul><li>8 (AI 1310)</li><li>155 (AS 1310)</li><li>310 (AS 1310 Gemini Configuration on Thermo Scientific TRACE™ 1300 GC, TRACE 1310 GC, and TRACE GC Ultra)</li><li><strong>Vial capacity: </strong>2 mL</li><li><strong>Optional micro-volume vials: </strong>300 µL</li><li><strong>Injections/vial:</strong> 0-99</li><li><strong>Viscosity delay: </strong>Yes/No</li></ul><h4><strong>Syringes</strong></h4><ul><li><strong>Standard</strong>: 10 µL</li><li><strong>Optional Micro-volume: </strong>5 µL</li><li><strong>Optional Nano-volume:</strong> 0.5 µL</li></ul><h4><strong>Injection parameters</strong></h4><ul><li><strong>Maximum volume: </strong>5 µL</li><li><strong>Minimum volume:</strong> 0.01 µL</li><li>Increments 0.01 µL steps</li></ul><h4><strong>Syringe rinsing</strong></h4><ul><li>Pre- and/or Post-injection</li><li><strong>Solvent selection:</strong> Single or combined mode</li><li>Sample pre-washes</li><li>Bubble elimination</li><li><strong>Solvent bottles</strong>: 4 x 4 mL</li><li><strong>Waste bottle capacity: </strong>40 mL</li></ul><h3><strong>Pre-set injection modes</strong></h3><h4><strong>“Minimum” needle depth</strong></h4><p>With this option, the syringe needle penetrates only partially in the inlet. Pre- and Post-injection dwell times are automatically set to zero. This selection enables “Cold Needle” type injections, preventing sample pre-volatilization from the needle. When operating in “Minimum” injection depth mode, all parameters are optimized and preset (Needle depth, pre- and post-dwell time, and Injection speed). Fast injection speed is optimized for this technique.</p><h4><strong>“Standard” needle depth</strong></h4><p>Using this option, the syringe needle penetrates entirely in the inlet. This selection offers the choice of pre- and post-injection injection dwell times, allowing to perform Hot Empty Needle type injections with the SSL inlet. This technique does not require any packing material in the liner. It should be preferred when analyzing thermally-labile compounds. Preset parameters are needle depth and injection speed. Manually set parameters are pre- and post-injection injection dwell times.</p><h4><strong>Reproducibility</strong></h4><p><strong>Chromatographic performance:</strong><br>&lt; 0.3 RSD % for C12, C16, C24 (C12-C24 alkane mix in hexane). Data obtained on 10 subsequent Splitless analyses, 1µL injected volume using “Standard” needle depth option.</p><h4><strong>Carryover</strong></h4><p>&lt; 0.001% measured by the residual area in a heptane blank following the injection of pure C14 and using 4 post-washes in combined solvents A+B.</p><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/application::product.product/Thermo-TSQtm-9000-1300-as-1310.jpg" alt="Thermo Scientific AI/AS 1310 liquid sampling automation" width="null" height="null"></p>

Thermo Scientific™ TRACE™ 1300 Series Gas Chromatograph

Modular GC system with instant-connect injectors and detectors for fast setup, low maintenance, and high-throughput routine analysis with helium-saving capability.

<h4><strong>Modular, fast, and robust GC system for modern analytical labs</strong></h4><p><strong>The TRACE 1300 Series GC platform offers a uniquely modular design that combines productivity, simplicity, and operational flexibility. With instant-connect user-exchangeable injectors and detectors, the system enables tool-free configuration changes in under 2 minutes. Designed for high-throughput QA/QC and routine labs, it reduces downtime and cost of ownership while delivering industry-leading performance.</strong></p><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/application::product.product/Trace-1300-GC.jpg-650.jpg" alt="Thermo Scientific™ TRACE™ 1300 Series Gas Chromatograph" width="null" height="null"></p><h3><strong>Key Features and Benefits</strong></h3><h4>⚙️ <strong>Modular Design with Instant Connect Technology</strong></h4><ul><li>Plug-in injector and detector modules install in minutes without tools</li><li>No need for service engineers or downtime during reconfiguration</li><li>Dual-channel and multi-detector setups supported</li><li>Ideal for evolving lab needs and future upgrades</li></ul><h4>💨 <strong>Exceptional Speed and Thermal Performance</strong></h4><ul><li>Ultra-fast oven with heating rates up to <strong>125 °C/min</strong></li><li>Oven cooldown from 450 °C to 50 °C in under 4 minutes</li><li>Retention time RSD &lt; <strong>0.0008 min</strong>, peak area RSD &lt; <strong>0.5%</strong></li><li>IEC (Integrated Electronic Control) for precise pressure and flow control</li></ul><h4>♻️ <strong>Helium Saver and Alternative Gas Compatibility</strong></h4><ul><li><strong>Instant Connect Helium Saver Injector</strong> reduces helium use by 90%+</li><li>Supports nitrogen or hydrogen as alternative carrier gases</li><li>Extend helium cylinder life up to <strong>14 years</strong> without method changes</li></ul><h4>🔁 <strong>Injection Versatility</strong></h4><ul><li>Split/splitless (SSL), PTV, Gas Sampling Valve, and On-column injection</li><li>Large volume injections and backflush options available</li><li>Cryogenic cooling options down to <strong>–100 °C</strong></li></ul><h4>🔬 <strong>Flexible Detector Options</strong></h4><ul><li>Instant Connect detectors: <strong>FID, TCD, ECD, NPD, FPD</strong></li><li>Miniaturized cells with fast acquisition rates up to <strong>300 Hz</strong></li><li>Connects seamlessly with Thermo Scientific GC-MS systems or FT-IR</li><li>Optional methanizer for CO/CO₂ detection</li></ul><h4>🧠 <strong>Smart Software Integration</strong></h4><ul><li>Full control via <a target="_blank" rel="noopener noreferrer" href="https://gcms.labrulez.com/products/76"><strong>Chromeleon™</strong></a><strong>, </strong><a target="_blank" rel="noopener noreferrer" href="https://lcms.labrulez.com/products/1758"><strong>Xcalibur™</strong></a><strong>, Chrom-Card™</strong></li><li>eWorkflows and intelligent automation for efficient operation</li><li>Dynamic data processing, QA/QC checks, and LIMS integration</li></ul><h3><strong>Additional Benefits</strong></h3><ul><li><strong>TRACE 1300 model:</strong> budget-friendly, simple interface for routine use</li><li><strong>TRACE 1310 model: </strong>touch screen interface for method development</li><li>Small footprint, low energy consumption, and fast startup</li><li>GLP-compliant modules, multilingual UI, and remote operability</li></ul><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/application::product.product/Thermo-TriPlustm-100-LS-Liquid-Autosampler-5.jpg" alt="Thermo Scientific™ TRACE™ 1300 Series Gas Chromatograph" width="null" height="null"></p>

Products distributed by Thermo Fisher Scientific (EMEA) - page 11

Related content

Discovery analysis for GCxGC trends using alteration and 2D correlation (Chris Freye, MDCW 2026)

News from LabRulezGCMS Library - Week 07, 2026

How to Protect Your GC Column - Part 2