<p><strong>Concerns about injecting water into a GC system largely come from older column designs, where stationary phases were simply coated and could be affected by water exposure. Modern capillary columns are typically chemically bonded, which improves resistance to water injections and even supports water rinsing in many cases.</strong></p><p>One practical exception involves <strong>very polar polyethylene glycol </strong>(PEG / “wax”) phases. Because these phases strongly interact with water, repeated aqueous injections can allow water to accumulate and gradually shift selectivity. For many PEG-based columns, minimizing frequent water injections helps maintain consistent performance.</p><p>A separate—and often more important—issue is water’s<strong> very large vapor expansion in a hot inlet</strong>. If the vapor volume exceeds the inlet liner capacity, backflash can occur, sending sample vapor into cooler, unheated zones and increasing the risk of carryover. Using smaller injection volumes helps reduce this risk.</p><p>In workflows where water is the<strong> sample matrix </strong>(for example, volatile analysis), analytes may elute at relatively low oven temperatures while water and higher-boiling residues can linger. Periodic bake-off (high-temperature cleanup steps) is commonly used to restore column performance when water remains on the phase at low temperatures.</p><p>In summary, the biggest hesitation about water injections is rooted in legacy, coated column stories. With chemically bonded phases, the key considerations tend to be inlet expansion/backflash behavior, water retention on very polar phases, and routine maintenance practices like bake-out.</p><blockquote><h4><a target="_blank" rel="noopener noreferrer" href="https://gcms.labrulez.com/products/1571"><strong>Zebron ZB-WAX</strong><i><strong>PLUS</strong></i><strong> GC Columns</strong></a></h4><ul><li>100% aqueous stable, excellent for aqueous samples; bonded and solvent rinseable</li><li>Extremely inert for acidic compounds</li><li>Enhanced selectivity for low boiling solvents; high retention of alcohols and chlorinated solvents</li><li>Increased efficiency at 20&nbsp;°C</li></ul></blockquote>

Water in GC: Safe or Risky? Here’s What You Need to Know

<p><strong>🎤 Presenter:</strong> <strong>Paul-Albert Schneide </strong>(University of Copenhagen)</p><p>💾 <a target="_blank" rel="noopener noreferrer" href="https://gcms.labrulez.com/paper/32780"><strong>PDF presentation</strong></a></p><h3><strong>Abstract</strong></h3><p><strong>Tensor decomposition methods such as PARAFAC and PARAFAC2 have been proposed for resolving co-elutions, and extracting purified spectra in two-dimensional chromatography datasets. However, the application of these methods is usually restricted to local regions-of-interest (ROIs). Therefore, additional pre-processing steps, are required and processing multiple samples at once can be difficult due to retention time shifts (e.g., it is difficult to define a ROI that captures the same analyse signal in multiple samples).</strong></p><p>This work presents an application of fast, shift-invariant tensor decomposition, which was used for the decomposition of full-scale GCxGC-VUV datasets. The results show that chemical groups can be resolved, which are non-separable with conventional, template-based approaches, such as aliphates and olefines, Furthermore, the extracted peak areas are in good agreement with the quantitative results of the reference methods (e.g., bromine number for olefines).</p><h2><strong>Video Transcription</strong></h2><h3><strong>Background and Motivation</strong></h3><p>The project originated from a collaboration initiated by Alexandra Alvich from IFPEN, who approached Prof. Rasmus Bro’s research group at the University of Copenhagen for help analyzing a GC×GC-VUV dataset acquired during her PhD research. The work was then continued by Paul-Albert Schneider and Jesper Henri from the Technical University of Denmark.</p><p>The primary objective was to develop a simpler and less manually intensive approach for petrochemical group quantification while maintaining strong quantitative performance and spectral interpretability.</p><p>According to Schneider, the proposed method is based on two key principles:</p><ul><li>Simple implementation with a minimal number of tuning parameters</li><li>Accurate estimation of peak patterns, VUV spectra, and peak areas</li></ul><p>The workflow specifically targets group-level petrochemical analysis rather than individual compound identification.</p><h3><strong>Data Analysis Workflow</strong></h3><p>The presented workflow begins with a collection of GC×GC-VUV measurements. In this study, the researchers analyzed:</p><ul><li>14 gas oil samples</li><li>24 total measurements, including replicates</li><li>Samples processed using different treatment methods</li></ul><p>Initial preprocessing was performed using a dedicated plug-in module developed during Alexandra Alvich’s PhD work. The preprocessing included:</p><ul><li>Signal smoothing</li><li>Downsampling</li><li>Basic data conditioning</li></ul><p>The processed data were then submitted to the decomposition engine developed by the Copenhagen research group. The decomposition produced:</p><ul><li>Resolved VUV spectra</li><li>GC×GC chromatographic landscapes</li><li>Peak areas or peak volumes</li></ul><p>An in-house spectral library from IFPEN was subsequently used to verify that the extracted spectra corresponded to known petrochemical groups, enabling group-level quantitative analysis.</p><p>Importantly, the workflow currently requires only a single major tuning parameter: the number of components used in the decomposition model. The researchers also noted ongoing efforts to automate this selection step.</p><h3><strong>Comparison with Existing Template-Based Methods</strong></h3><p>The study benchmarked the new approach against Alexandra Alvich’s previously developed template-based quantification method.</p><p>In the template-based workflow:</p><ul><li>Elution regions are predefined using a grid structure</li><li>Peak intensities within those regions are summed</li><li>Quantitative estimates are obtained for specific petrochemical classes</li></ul><p>Although the template-based strategy demonstrated strong performance compared with other analytical techniques, Schneider highlighted several limitations:</p><ul><li>Sensitivity to retention time shifts</li><li>Manual adjustment of integration regions</li><li>Dependence on prior knowledge of coeluting compounds</li></ul><p>The new decomposition-based method was designed to reduce manual intervention and improve robustness against chromatographic variability.</p><h3><strong>Shift-Invariant Trilinear Decomposition</strong></h3><p>The proposed workflow is conceptually related to PARAFAC and multivariate curve resolution methods.</p><p>One important advantage of GC×GC-VUV data is the applicability of the Beer–Lambert law, which enables mathematically structured decomposition approaches.</p><p>The researchers evaluated two possible strategies:</p><ol><li>Decomposing each sample individually</li><li>Decomposing all samples simultaneously after concatenation into one large dataset</li></ol><p>The second strategy became the central focus of the work. Multiple samples were concatenated into a large matrix and factorized to extract shared chemical information across all measurements simultaneously.</p><p>Unlike many conventional GC×GC deconvolution pipelines, the workflow does not rely on a prior region-of-interest detection step. Instead, the entire dataset is decomposed directly.</p><h3><strong>Addressing Retention Time Shifts</strong></h3><p>A critical challenge for PARAFAC-type models is the assumption of strict trilinearity. In GC×GC datasets, however, second-dimension retention time shifts caused by temperature programming violate this assumption.</p><p>Schneider demonstrated how standard one-component PARAFAC models fail to properly model shifted peaks, leaving characteristic residual patterns. When fitting additional components, conventional models often allocate extra components to describing peak shifts instead of resolving true coeluting compounds.</p><p>The shift-invariant model solves this issue by explicitly accounting for chromatographic shifts. As a result:</p><ul><li>Large shifted peaks are modeled correctly</li><li>Residuals are minimized</li><li>Small coeluting peaks become resolvable</li></ul><p>The algorithm uses fast Fourier transform (FFT)-based operations internally to correct for chromatographic shifts efficiently.</p><p>According to the presentation, the approach is also significantly faster than PARAFAC2, which is commonly used for shifted datasets.</p><p>The researchers additionally described extensions of the model that can accommodate:</p><ul><li>Retention time shifts</li><li>Peak shape variations</li><li>Additional flexibility without losing uniqueness properties</li></ul><h3><strong>Quantitative Results</strong></h3><p>The team applied a seven-component model to the complete dataset containing 24 GC×GC-VUV measurements.</p><p>The decomposition extracted seven characteristic VUV spectra, which were compared against the IFPEN in-house spectral library. The extracted spectra matched known petrochemical group signatures very well.</p><p>The resolved components included:</p><ul><li>Two monoaromatic components</li><li>Two diaromatic components</li><li>Additional petrochemical group patterns</li></ul><p>For quantitative evaluation, chemically related components were grouped together.</p><h4><strong>Reproducibility</strong></h4><p>Replicate measurements demonstrated strong quantitative reproducibility:</p><ul><li>Relative standard deviations below 10%</li><li>Consistent peak area estimation across petrochemical groups</li></ul><h4><strong>Comparison with the Template-Based Approach</strong></h4><p>The decomposition workflow showed good agreement with the existing template-based quantification strategy, with monoaromatics representing the main discrepancy requiring further investigation.</p><p>Schneider explained that the differences were likely related to relative response factor scaling used in the template-based method but not yet implemented in the decomposition workflow at the time of the presentation.</p><h4><strong>Future Development</strong></h4><p>The researchers outlined several next steps for the project:</p><ul><li>Running models on individual samples to achieve higher resolution</li><li>Resolving sulfur-containing compounds</li><li>Extracting more sample-specific differences</li><li>Automating component number selection</li><li>Investigating deviations in monoaromatic quantification</li><li>Integrating the workflow into an open-source software project</li></ul><p>The team also expressed interest in future collaboration with other researchers working on related GC×GC data analysis workflows.</p><h3><strong>Conclusion</strong></h3><p>The presented shift-invariant trilinear decomposition workflow demonstrated promising performance for automated petrochemical group analysis in GC×GC-VUV datasets. By combining robust mathematical modeling with minimal manual intervention, the method offers a simplified alternative to traditional template-based approaches while maintaining strong quantitative agreement and spectral interpretability.</p><p>The work highlights the growing role of advanced multivariate data analysis strategies in comprehensive chromatography and demonstrates how shift-aware decomposition methods can significantly improve the analysis of highly complex petrochemical datasets.</p><blockquote><p><strong>This text has been automatically transcribed from a video presentation using AI technology. It may contain inaccuracies and is not guaranteed to be 100% correct.</strong></p></blockquote>

One-shot tensor decomposition of full-scale GC×GC-VUV datasets for resolving petrochemical groups (Paul-Albert Schneide, MDCW 2026)

<p><strong>Our Library never stops expanding. What are the most recent contributions to LabRulezGCMS Library in the week of 11th May 2026? Check out new documents from the field of the gas phase, especially GC and GC/MS techniques!</strong></p><blockquote><p><span style="font-size:20px;">👉 </span><a target="_blank" rel="noopener noreferrer" href="https://gcms.labrulez.com/library"><span style="font-size:20px;"><strong>SEARCH THE LARGEST REPOSITORY OF DOCUMENTS ABOUT GCMS AND RELATED TECHNIQUES</strong></span></a></p></blockquote><blockquote><p><strong>👉 Need info about different analytical techniques?</strong> Peek into <a target="_blank" rel="noopener noreferrer" href="https://lcms.labrulez.com/library"><strong>LabRulezLCMS</strong></a> or <a target="_blank" rel="noopener noreferrer" href="https://icpms.labrulez.com/library"><strong>LabRulezICPMS</strong></a> libraries.</p></blockquote><p>This week we bring you application note by<strong> Shimadzu, </strong>poster by <strong>MDCW / William &amp; Mary</strong> and brochure by <strong>Thermo Fisher Scientific!</strong></p><h3><strong>1. MDCW / William &amp; Mary: Optimizing Solvent Selection and Data Reduction Workflows for GC×GC Fire Debris Analysis</strong></h3><ul><li>Poster</li><li><a target="_blank" rel="noopener noreferrer" href="https://gcms.labrulez.com/labrulez-bucket-strapi-h3hsga3/P_14_O_Brien_63304669ee.pdf"><strong>Full PDF for download</strong></a></li></ul><section><div><div><div><div><div><div><h5><strong>What are Ignitable Liquid Residues (ILRs)?&nbsp;</strong></h5><ul><li>Chemical remains of ignitable liquids (IL) (e.g., gasoline or diesel) that did not fully burn during a fire&nbsp;</li><li>ILRs are usually petroleum-based products and contain complex mixtures of volatile chemicals, like hydrocarbons&nbsp;</li></ul><h5><strong>Forensic Analysis of ILRs&nbsp;</strong></h5><ul><li>Collection of porous materials like wood from the fire’s point of origin&nbsp;</li><li>Must be stored in airtight containers to prevent volatile ILR from evaporation&nbsp;</li><li>Passive headspace extraction onto activate charcoal strips (ACS) is used to extract ILRs from debris, and dichloromethane (DCM) is used to extracts ILRs from charcoal strips&nbsp;</li><li>Emerging is the use of two-dimensional gas chromatography – time of fight - mass spectrometry (GC×GC-TOFMS), with higher separation and resolution</li><li>Resulting chromatograms presents a pattern of peaks which can be used to identified specific type of accelerant used&nbsp;</li></ul><h5><strong>Chemometrics&nbsp;</strong></h5><ul><li>The discipline that focuses on the application of statistical and mathematical methods to analyze chemical data and extract meaningful information (Bovens, 2019)&nbsp;</li><li>Helps make sense of large datasets from analytical instruments, find pattens, and classify samples</li></ul><h4><strong>Methods</strong></h4><h5><strong>Analytical Instrumentation&nbsp;</strong></h5><ul><li>LECO corporation <a target="_blank" rel="noopener noreferrer" href="https://gcms.labrulez.com/products/1097"><strong>BTX4D GC×GC-TOFMS</strong></a> with <a target="_blank" rel="noopener noreferrer" href="https://gcms.labrulez.com/products/1289"><strong>Paradigm Shift reverse fill-flush (RFF) flow modulator</strong></a></li></ul><h5><strong>Software&nbsp;</strong></h5><ul><li><a target="_blank" rel="noopener noreferrer" href="https://gcms.labrulez.com/products/1873"><strong>ChromaTOF Sync 2D</strong></a> (LECO corporation)&nbsp;</li><li>R Statistical Software</li></ul><h4><strong>Conclusions</strong></h4><p>This study demonstrated that the use of chemometrics can be integrated into a data processing workflow to better understand data sets and create a streamlined process. Using UMAP, patterns identified that were not originally seen in PCA lead to the preferred solvents of ILR extraction being hexane and methanol. Since UMAP allowed visualization of local and global structures, groupings of gasoline samples allowed for better analysis of solvent effect.</p><h3><strong>2. Shimadzu: Multiresidue Pesticides Analysis in Solvent Extract of Annatto (Natural Color Additive) Using </strong><a target="_blank" rel="noopener noreferrer" href="https://gcms.labrulez.com/library?mainauthorItems=1&amp;search=GCMS-TQ8050+NX"><strong>GCMSTQ8050 NX</strong></a></h3><ul><li>Application note</li><li><a target="_blank" rel="noopener noreferrer" href="https://gcms.labrulez.com/labrulez-bucket-strapi-h3hsga3/an_06_sip_gc_043_en_95576a9ac4.pdf"><strong>Full PDF for download</strong></a></li></ul><h5><strong>User Benefits</strong></h5><ul><li>&nbsp;Accurate and reproducible trace level quantitation of pesticides in highly pigmented complex matrix using Ultra-fast GCMSTQ8050 NX and QuEChERS extraction</li><li>Single-laboratory partial validated method for LOQ determination meeting regulatory guidelines</li><li>Ease of instrumental method optimization using GCMS Smart Pesticides Database Ver.2 from Shimadzu Corporation</li></ul><p>Annatto is an orange-red condiment and food colorant derived from the seeds of the achiote tree (Bixa Orellana) (Fig. 1). It is often used to impart a yellow to red-orange color to foods, but sometimes also for its flavor and aroma. Similar effects can be obtained by extracting some of the color and flavor principles from the seeds, which are then added to the food. Annatto and its extracts are now widely used in an artisanal or industrial scale as a coloring agent in many processed food products, such as cheeses, butter, baked goods, potatoes, snack foods, breakfast cereals, smoked fish etc. In these uses, Annatto is a natural alternative to synthetic food coloring compounds.&nbsp;</p><p>Owing to its large culinary uses and other diverse applications, use of chemical pesticides for its production in large quantities is imperative. Dye extraction process may result in concentration of pesticides and in turn contribute to adverse impact on human health when incorporated in various preparations. Hence quantitation of residual pesticides in Annatto extract becomes very important. As the oleoresin is a complex matrix, it is required to develop a rugged, sensitive and efficient method for extraction of residual pesticide and its analysis.&nbsp;</p><p>This study reports a highly sensitive method for simultaneous quantification of multiple pesticides in highly pigmented complex matrix of Annatto using modified QuEChERS[1] with triple quadrupole gas chromatography (GC-MS/MS) system.</p><h4><strong>Materials and Methods</strong></h4><p>For this study, customized reference standard mixture of most commonly observed pesticides in Annatto seeds was procured from Restek Corporation.</p><p>The calibration standards were analyzed from 0.5 to 1000 μg/L. Linearity was plotted by external standard method and using weighted regression of 1/C2. Sample was spiked at 3 levels i.e., 10, 25 and 100 μg/kg. Recovery samples were prepared in 6 replicates at each level. <a target="_blank" rel="noopener noreferrer" href="https://gcms.labrulez.com/library?mainauthorItems=1&amp;search=GCMS-TQ8050+NX"><strong>GCMS-TQ8050 NX</strong></a> (Fig. 2), manufactured by Shimadzu Corporation Japan, was used for quantitation. LabSolutions InsightTM was used for data processing, which helped in evaluating validation parameters with ease.</p><h4><strong>Conclusion</strong></h4><p>This study shows that the modified QuEChERS method combined with GC-MS/MS system is a reliable and efficient tool to quantify residual pesticides in Annatto extract sample. Although Annatto extract is a highly pigmented complex matrix, the modified QuEChERS method significantly reduces interference. Also, extremely sensitive Shimadzu GC-MS/MS allows trace level detection even after multifold dilution of sample. This helps in reducing contamination and enhancing ruggednessresulting in reproducible detection of analytes.</p><h3><strong>3. Thermo Fisher Scientific: Sentinel PRO 710 environmental mass spectrometer Precise real time gas analyzer for toxic volatile organic compounds</strong></h3><ul><li>Product specification</li><li><a target="_blank" rel="noopener noreferrer" href="https://gcms.labrulez.com/labrulez-bucket-strapi-h3hsga3/sentinel_pro_710_spec_sheet_en_886523bfc2.pdf"><strong>Full PDF for download</strong></a></li></ul><p>The <a target="_blank" rel="noopener noreferrer" href="https://gcms.labrulez.com/library?mainauthorItems=3&amp;search=Sentinel+PRO"><strong>Thermo Scientific™ Sentinel PRO Environmental Mass Spectrometer </strong></a>is a highly reliable and versatile gas analyzer ideal for reporting the presence of toxic VOCs from fugitive emissions in industrial settings to ensure worker safety.</p><h4><strong>Fugitive emissions of toxic VOCs&nbsp;</strong></h4><p>Wherever there is potential danger for fugitive emissions of toxic organic vapors from a chemical production unit, regulating authorities often require plants to keep records of ambient vapor concentrations to protect workers from exposure. Various forms of capture include evacuated vessels, organic vapor monitors, or purge and trap devices, all of which require samples to be sent for analysis. Alternatively, electrochemical sensors or open path FT-IR spectroscopy can provide more immediate results. However, none of these technologies are capable of providing the spatial and temporal resolution required to qualify as actionable information.&nbsp;</p><h4><strong>Analytical platform&nbsp;</strong></h4><p>The primary feature of the Sentinel PRO mass spectrometer is the magnetic sector analyzer. This field-proven technology has demonstrated the strongest performance for industrial on-line gas analysis. Magnetic sector technology offers precision, accuracy, long intervals between calibrations. The new touchscreen interface further enhances usability, providing intuitive in-person operation, simplified maintenance, and real-time data viewing. Multi-role user permissions ensure security and control allowing operators to customize settings based on their specific needs.&nbsp;</p><h4><strong>Comprehensive data collection&nbsp;</strong></h4><p>With speed and precision, the Sentinel PRO analyzer monitors all the critical areas for short-term exposure levels of toxic VOCs, and also provides accurate and time-weighted average exposure data. With a high number of sample points available, many can be located close to potential leak points such as valve stems, etc., enabling leak detection and correction before any toxic hazard is created.&nbsp;</p><h4><strong>Membrane inlet mass spectrometry&nbsp;</strong></h4><p>The analyzer is fitted with a membrane inlet to reduce the pressure of the sample air from atmospheric to the working pressure of the enclosed ion source. This allows a method of sample introduction that greatly enhances the system’s sensitivity to VOCs. Since the membrane is more permeable to VOCs than to major air gases, it provides enrichment by several orders of magnitude, enabling detection as low as 5 ppb (species dependent) permits easy membrane replacement during annual routine maintenance to minimize downtime and increase productivity.</p></div></div></div></div></div></div></section>

News from LabRulezGCMS Library - Week 20, 2026

Article

Product

Application

Academy

Presentation

Video

Poster

The Multidimensional Chromatography (MDC) Workshop draws experts in this exciting field to share and discuss their research.

The Multidimensional Chromatography Workshop

Everything from the world of analytical chemistry in one place. We connect people in solving their problems. At Labrulez you will find all the necessary information easily, quickly and clearly. Stop searching and start finding.

LabRulez

Phenomenex is a global technology leader committed to developing novel analytical chemistry solutions that solve the separation and purification challenges of researchers in industrial, government and academic laboratories.

Phenomenex

Phenomenex Strata C18-E Solid Phase Extraction (SPE)

Strata C18-E is a silica-based end-capped C18 solid phase extraction (SPE) sorbent.

<p><strong>Strong Hydrophobic Retention Solid Phase Extraction (SPE)</strong></p><p>Strata C18-E is a <strong>silica-based</strong> <strong>end-capped C18</strong> solid phase extraction (SPE) sorbent that offers <strong>strong hydrophobic retention</strong> with negligible secondary polar interactions from active silanol groups. Strata C18-E can be best used for the <strong>extraction of hydrophobic</strong> or <strong>polar organic analytes</strong> from <strong>aqueous matrices</strong>. In addition, Strata SPE sorbents are manufactured with the highest purity and extensively tested to give clean extracts.</p><p>Strata C18-E is <strong>compatible</strong> with various formats, including <strong>C18 SPE cartridges</strong>. Our C18 SPE products are synonymous with quality, offering the highest purity and undergo rigorous testing to deliver consistently clean extracts for your analytical needs.</p><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Phenomenex_Strata_C18_E_748c192b52.webp" alt="Phenomenex: Strata-C18-E" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Phenomenex_Strata_C18_E_748c192b52.webp 245w," sizes="100vw" width="500" height="150"></p><ul><li><strong>Surface Area (m²/g)</strong>: 500, m²/g</li><li><strong>Separation Mode:</strong> Reversed Phase</li><li><strong>Pore Size:</strong> 70, 100</li><li><strong>Particle Size:</strong> 20, 55</li><li><strong>Recommended Use: </strong>Extraction of hydrophobic molecules</li></ul><h4><strong>Starting Method</strong></h4><h5><strong>Strata Reversed Phase</strong></h5><ul><li><strong>Condition:</strong> 1 mL Methanol</li><li><strong>Equilibrate:</strong> 1 mL DI Water</li><li><strong>Load:</strong> Pretreated sample</li><li><strong>Wash</strong>: 1 mL 5% Methanol in DI Water, dry under vacuum for 2-5 min</li><li><strong>Elute:</strong> 1 mL Methanol</li></ul><p>Based on 100 mg/1 mL sorbent mass. The above is a convenient starting point for SPE method development, further optimization may be required to tailor the method for your specific extraction needs.</p>

Phenomenex Strata Screen-A Solid Phase Extraction (SPE)

Incorporates the hydrophobic selectivity of a C8 phase and strong anion-exchange for the extraction of acidic drugs from biological matrices.

<p><strong>Mixed-Mode Solid Phase Extraction (SPE) Sorbent</strong></p><p>Incorporates the hydrophobic selectivity of a C8 phase and strong anion-exchange for the extraction of acidic drugs from biological matrices.</p><figure class="image"><img style="aspect-ratio:500/150;" src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Phenomenex_Strata_Screen_A_f370bdfd48.webp" alt="Phenomenex: Strata Screen-A" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Phenomenex_Strata_Screen_A_f370bdfd48.webp 245w," sizes="100vw" width="500" height="150"></figure><ul><li><strong>Surface Area (m²/g)</strong>: -</li><li><strong>Separation Mode:</strong> Multi-Mode</li><li><strong>Particle Size:</strong> 55</li><li><strong>Recommended Use: </strong>Extracts acidic drugs from biological matrices</li></ul><h4><strong>Starting Method</strong></h4><h5><strong>Strata Screen-A Strong Anion-Exchange</strong></h5><ul><li><strong>Condition:</strong> 1 mL Methanol</li><li><strong>Equilibrate:</strong> 1 mL Water</li><li><strong>Load:</strong> Pretreated sample</li><li><strong>Wash 1</strong>: 1 mL 25mM Ammonium Acetate Buffer, pH 6-7</li><li><strong>Wash 2</strong>: 1 mL Methanol, dry under vacuum for 2-5 min</li><li><strong>Elute: </strong>1 mL 5% Formic Acid in Methanol</li></ul><p>Based on 100 mg/1 mL sorbent mass. The above is a convenient starting point for SPE method development, further optimization may be required to tailor the method for your specific extraction needs.</p>

Phenomenex Strata Screen-C Solid Phase Extraction (SPE)

Incorporates the hydrophobic selectivity of a C8 phase and strong cation exchange for the extraction of basic drugs from biological matrices.

<p><strong>Strong Cation-Exchange Solid Phase Extraction (SPE)</strong></p><p>Incorporates the hydrophobic selectivity of a C8 phase and strong cation exchange for the extraction of basic drugs from biological matrices.</p><figure class="image"><img style="aspect-ratio:500/150;" src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Phenomenex_Strata_Screen_C_b60bb2b7e4.webp" alt="Phenomenex: Strata Screen-C" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Phenomenex_Strata_Screen_C_b60bb2b7e4.webp 245w," sizes="100vw" width="500" height="150"></figure><ul><li><strong>Surface Area (m²/g)</strong>: 500, m²/g, 500 m²/g</li><li><strong>Separation Mode:</strong> Multi-Mode</li><li><strong>Pore Size</strong>: 70</li><li><strong>Particle Size:</strong> 55</li><li><strong>Recommended Use: </strong>Extraction of basic drugs from biological matrixes</li></ul><h4><strong>Starting Method</strong></h4><h5><strong>Strata Screen-C Strong Cation-Exchange</strong></h5><ul><li><strong>Condition:</strong> 1 mL Methanol</li><li><strong>Equilibrate:</strong> 1 mL Acidified Water</li><li><strong>Load:</strong> Pretreated sample (acidified)</li><li><strong>Wash 1</strong>: 1 mL 0.1N HCl in Water</li><li><strong>Wash 2</strong>: 1 mL 0.1N HCl in Methanol, dry under vacuum for 2-5 min</li><li><strong>Elute: </strong>1 mL 5 % NH<sub>4</sub>OH in Methanol</li></ul><p>Based on 100 mg/1 mL sorbent mass. The above is a convenient starting point for SPE method development, further optimization may be required to tailor the method for your specific extraction needs.</p>

Phenomenex Strata Screen-C GF Solid Phase Extraction (SPE)

Optimized for gravity flow, this sorbent offers hydrophobic selectivity from a C8 phase and strong cation-exchange properties for the extraction of basic drugs.

<p><strong>Strong Cation-Exchange Solid Phase Extraction (SPE)</strong></p><p>Optimized for gravity flow, this sorbent offers hydrophobic selectivity from a C8 phase and strong cation-exchange properties for the extraction of basic drugs from biological matrixes. Offers the selectivity of Screen-C in a gravity flow particle size for viscous samples.</p><h4><strong>Starting Method</strong></h4><h5><strong>Strata Screen-C GF Strong Cation-Exchange</strong></h5><ul><li><strong>Condition:</strong> 1 mL Methanol</li><li><strong>Equilibrate:</strong> 1 mL Acidified Water</li><li><strong>Load:</strong> Pretreated sample (acidified)</li><li><strong>Wash 1</strong>: 1 mL 0.1N HCl in Water</li><li><strong>Wash 2</strong>: 1 mL 0.1N HCl in Methanol, dry under vacuum for 2-5 min</li><li><strong>Elute: </strong>1 mL 5 % NH<sub>4</sub>OH in Methanol</li></ul><p>Based on 100 mg/1 mL sorbent mass. The above is a convenient starting point for SPE method development, further optimization may be required to tailor the method for your specific extraction needs.</p>

Waters Oasis SPE products

Waters Oasis SPE products come in a broad range of sorbents and an array of formats. With Oasis products, you can meet a wide variety of sample preparation needs.

<h4><strong>Faster, cleaner, and simpler SPE starts here</strong></h4><p>Analytical chemists worldwide use SPE to remove interfering matrix compounds and enrich the analyte of interest to ensure the generation of high-quality data.</p><p>Waters Oasis SPE products come in a broad range of sorbents and an array of formats. With Oasis products, you can meet a wide variety of sample preparation needs, from simple and fast sample matrix clean-up to more complex sample preparation challenges.</p><p>Oasis SPE products deliver unmatched purity, consistency, and quality for sample analysis. Along with seven different SPE chemistries, Oasis SPE products use universal to customized protocols to handle your unique sample.</p><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Waters_Oasis_SPE_kolonky_2_967d461f2e/Waters-Oasis-SPE-kolonky-2.jpg" alt="Waters: Oasis SPE" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Waters_Oasis_SPE_kolonky_2_967d461f2e/thumbnail_Waters-Oasis-SPE-kolonky-2.jpg 245w," sizes="100vw" width="950" height="416"></p><h4><strong>Overview</strong></h4><ul><li>Fully water-wettable sorbents increase reproducibility and enable elimination of condition and equilibration steps</li><li>Co-polymer pH stable from 0–14 with no secondary silanol activity</li><li>Optimal sensitivity for small molecule and therapeutic peptide analysis</li><li>Reduced matrix effects for LC-MS/MS analyses</li><li>Unsurpassed selectivity</li><li>Consistent retention and capacity, yielding the highest SPE recovery</li><li>Reduces variability in analytical results and increases robustness of analysis</li><li><strong>Recommended Use: </strong>For the fastest, cleanest, and simplest approach to SPE-LC-MS/MS method development.</li></ul><h4><strong>Solid-Phase Extraction Chemistries</strong></h4><h5><strong>Oasis PRiME HLB</strong></h5><ul><li>Multi-purpose hydrophilic-lipophilic balanced reversed phase sorbent for acids, bases, and neutrals</li><li>Cleaner samples in fewer steps with simple three-and two-step protocols, no SPE expertise required</li><li>Removes 95% of common matrix interferences, such as proteins, salts, phospholipids, and pigments</li><li>No sorbent conditioning or equilibration steps required</li><li>Faster, more predictable analysis time</li><li>Ideal for reversed-phase SPE clean-up of samples in routine analysis.</li></ul><h5><strong>Oasis PRiME MCX</strong></h5><ul><li>Mixed-mode Cation eXchange sorbent to selectively retain, concentrate and elute basic compounds</li><li>Reversed-phase and ion-exchange functionality for orthogonal sample preparation</li><li>Cleaner samples in fewer steps with simple and fast 3 and 4-step protocols</li><li>Removes 99% of phospholipids from complex sample matrices</li><li>No sorbent conditioning or equilibration steps required</li><li>Faster, more predictable analysis time</li><li>Highly reproducible target analyte recoveries</li><li>Ideal for basic compound specificity while removing matrix interferences in a simple clean-up.</li></ul><h5><strong>Oasis HLB</strong></h5><ul><li>Multi-purpose hydrophilic-lipophilic balanced reversed phase sorbent</li><li>Provides high capacity for acids, bases, and neutrals</li><li>Ideal for ultra-high capacity of very polar compounds.</li></ul><h5><strong>Oasis MCX</strong></h5><ul><li>Mixed-mode Cation eXchange sorbent for bases</li><li>Increased analyte specificity and sensitivity</li><li>Reversed-phase and ion-exchange functionality for orthogonal sample preparation</li><li>Ideal for selective retention of basic analytes.</li></ul><h5><strong>Oasis MAX</strong></h5><ul><li>Mixed-mode Anion eXchange for acids</li><li>Increased analyte specificity and sensitivity</li><li>Reversed-phase and ion-exchange functionality for orthogonal sample preparation</li><li>Ideal for selective retention of acidic analytes.</li></ul><h5><strong>Oasis WAX</strong></h5><ul><li>Weak Anion eXchange mixed-mode sorbent for strong acidic compounds</li><li>Increased analyte specificity and sensitivity</li><li>Reversed-phase and ion-exchange functionality for orthogonal sample preparation</li><li>Ideal for improved retention of strong acidic compounds.</li></ul><h5><strong>Oasis WCX</strong></h5><ul><li>Weak Cation eXchange mixed-mode sorbent for strong basic compounds</li><li>Increased analyte specificity and sensitivity</li><li>Reversed-phase and ion-exchange functionality for orthogonal sample preparation</li><li>Ideal for improved retention of all basic analytes, especially strong bases.</li></ul><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Waters_Sorbenty_Oasis_SPE_na_bazi_kopolymeru_Oasis_HLB_c8ffee39b3/Waters-Sorbenty-Oasis-SPE-na-bazi-kopolymeru-Oasis-HLB.png" alt="Waters: Oasis Sorbents" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Waters_Sorbenty_Oasis_SPE_na_bazi_kopolymeru_Oasis_HLB_c8ffee39b3/thumbnail_Waters-Sorbenty-Oasis-SPE-na-bazi-kopolymeru-Oasis-HLB.png 211w," sizes="100vw" width="1511" height="1119"></p><h4><strong>Oasis Formats</strong></h4><h5><strong>Oasis μElution Plate</strong></h5><ul><li>Patented μElution plate design</li><li>No evaporation and reconstitution necessary due to elution volumes as low as 25 µL</li><li>Ideal for SPE clean-up and analyte enrichment of small sample volumes</li><li>Compatible with most liquid-handling robotic systems for automated, reliable high-throughput SPE (HT-SPE)</li></ul><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Waters_Corporation_Oasis_m_Elution_Plate_aa7e36a4c1.jpg" alt="Waters: Oasis µElution Plate" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Waters_Corporation_Oasis_m_Elution_Plate_aa7e36a4c1.jpg 245w," sizes="100vw" width="502" height="260"></p><h5><strong>Oasis 96-Well Sample Extraction Plates</strong></h5><ul><li>Innovative, award-winning two-stage well design</li><li>High throughput and high recovery</li><li>Compatible with most liquid-handling robotic systems for automated, reliable high-throughput SPE (HT-SPE)</li></ul><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Waters_Corporation_Oasis_96_Well_Sample_Extraction_Plates_9528d532b9.jpg" alt="Waters: Oasis 96-Well Sample Extraction Plates" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Waters_Corporation_Oasis_96_Well_Sample_Extraction_Plates_9528d532b9.jpg 245w," sizes="100vw" width="525" height="329"></p><h5><strong>Oasis Syringe-Barrel Cartridges</strong></h5><ul><li>Ultra-clean syringe barrel and frits</li><li>Available in cartridges ranging from 1 cc to 60 cc</li><li>Flangeless syringe-barrel cartridges available in 1 cc, 3 cc, and 6 cc sizes</li><li>Plus-style cartridges with Luer inlet hub and outlet tip, compatible with hand-held syringes</li></ul><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Waters_Corporation_Oasis_Syringe_Barrel_Cartridges_961aa06b8a.jpg" alt="Waters Corporation: Oasis Syringe-Barrel Cartridges" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Waters_Corporation_Oasis_Syringe_Barrel_Cartridges_961aa06b8a.jpg 245w," sizes="100vw" width="503" height="311"></p><h5><strong>Oasis Glass Cartridges</strong></h5><ul><li>Ultra-clean glass syringe with Teflon® frit</li><li>For trace level detection and analysis at part-per-trillion (PPT) levels</li><li>Available in 5 cc (200 mg) configuration</li></ul><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Waters_Corporation_Oasis_Glass_Cartridges_5e96319c7f.jpg" alt="Waters: Oasis Glass Cartridges" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Waters_Corporation_Oasis_Glass_Cartridges_5e96319c7f.jpg 188w," sizes="100vw" width="409" height="339"></p><h5><strong>Oasis On-Line Columns and Cartridges</strong></h5><ul><li>For rugged, reproducible, and ultra-fast on-line analysis</li><li>Wide choice of configurations, particle sizes, and sorbent chemistries</li><li>Available with all six patented Oasis sorbents—PRiME HLB, HLB, MCX, MAX, WCX, and WAX</li><li>High recovery and reproducible results for a wide range of compounds</li><li>Cartridge format for use with Spark Holland Prospekt-2™/Symbiosis™ systems also available</li></ul><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Waters_Corporation_Oasis_On_Line_Columns_and_Cartridges_ba02114c92.jpg" alt="Waters: Oasis On-Line Columns and Cartridges" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Waters_Corporation_Oasis_On_Line_Columns_and_Cartridges_ba02114c92.jpg 168w," sizes="100vw" width="415" height="386"></p><h4><strong>Sample preparation, improved</strong></h4><p>Improving various aspects of chromatography and mass spectrometry analyses often starts with sample preparation. &nbsp;Solid-phase extraction (SPE) or "liquid-solid phase extraction" is a sample preparation technology that uses particles of chromatographic packing material, usually in a cartridge or 96-well plate format, to chemically separate different analytes and aid in removing matrix components in a sample. &nbsp;</p><p>SPE is a proven sample preparation tool for simple sample matrix removal, including common interferences like proteins, salts, fats and phospholipids. This matrix removal provides many benefits, including matrix effect reduction and an increase in sample concentration and analyte specificity. Matrix removal also significantly simplifies chromatographic complexity by reducing the number of interfering peaks in the LC and reducing signal suppression by providing clean samples for the MS.</p><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Waters_Corporation_Oasis_SPE_LC_MS_MS_chromatogram_of_1_pgm_L_of_alprazolam_from_rat_plasma_8b7275b25b.jpg" alt="Waters: Oasis SPE - LC-MS-MS chromatogram of 1 pgmL of alprazolam from rat plasma" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Waters_Corporation_Oasis_SPE_LC_MS_MS_chromatogram_of_1_pgm_L_of_alprazolam_from_rat_plasma_8b7275b25b.jpg 169w," sizes="100vw" width="1024" height="946"></p><h4><strong>Get the cleanest extracts with the Oasis 2x4 method</strong></h4><p>Having a variety of tools for method development allows separation scientists to optimize protocols for maximum sensitivity and selectivity. The Oasis 2x4 method for SPE sorbent and protocol selection for acids, bases, and neutrals produces the cleanest extracts – all by eliminating matrix interferences and sample variability. Get the flexibility to extract acids, bases, and neutrals with high SPE recoveries while removing matrix components that may interfere with analysis with our two protocols and four sorbents. By following the simple steps outlined in the Oasis 2x4 method, you can achieve high recoveries and the cleanest extracts.</p><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Waters_Oasis_2x4_protokol_pro_vyvoj_metody_c417be9006/Waters-Oasis-2x4-protokol-pro-vyvoj-metody.jpg" alt="Waters: Oasis SPE - Oasis 2 x 4 method development protocol." srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Waters_Oasis_2x4_protokol_pro_vyvoj_metody_c417be9006/thumbnail_Waters-Oasis-2x4-protokol-pro-vyvoj-metody.jpg 242w," sizes="100vw" width="1519" height="979"></p><h4><strong>Isolate your compounds with the Oasis HLB method</strong></h4><p>Solid-phase extraction (SPE) method development starts with knowledge of the sample matrix—the nature and relative concentration of the analytes of interest and potentially interfering endogenous compounds. The right sorbent and solvents are selected for load, wash, and elute steps, resulting in the creation of rugged, reliable, and selective protocols. The Oasis HLB method is a generic protocol used to isolate a broad range of acidic, basic, and neutral compounds from a wide spectrum of matrices.</p><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Waters_Corporation_Oasis_SPE_Generic_Method_Protocol_with_Oasis_HLB_SPE_83d684704d.jpg" alt="Waters: Oasis SPE - Generic Method Protocol with Oasis HLB SPE" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Waters_Corporation_Oasis_SPE_Generic_Method_Protocol_with_Oasis_HLB_SPE_83d684704d.jpg 139w," sizes="100vw" width="1024" height="1153"></p><h4><strong>Multiple contaminant analysis with the 2-step pass-through protocol</strong></h4><p>If you are doing multiple residue screening of veterinary drugs, pesticides and mycotoxins in various food matrices, you may be facing a high concentration of organic solvents. With our simple 2-step protocol (pass-through SPE), you can remove matrix interferences quickly if your samples contain a high concentration of organic solvent(s) and concentration and/or salt removal is not required. It can be used as the clean-up method following QuEChERS extraction, saving you significant time compared to the traditional dispersive SPE method - all while achieving superior clean-up.</p><p><strong>To do pass-through SPE, Waters offers 2 convenient and flexible formats:</strong></p><ul><li><strong>Traditional-style cartridges</strong> compatible with vacuum and positive pressure manifolds&nbsp;</li><li><strong>"Plus" style cartridges</strong> that can be used without manifolds when connected to a displacement syringe</li></ul><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Waters_Oasis_SPE_kolonky_3_b4da6242de/Waters-Oasis-SPE-kolonky-3.jpg" alt="Waters: Oasis Plus Light and Plus Short Cartridges for 2-step pass through protocol." srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Waters_Oasis_SPE_kolonky_3_b4da6242de/thumbnail_Waters-Oasis-SPE-kolonky-3.jpg 152w," sizes="100vw" width="1308" height="1342"></p>

Thermo Scientific QuEChERS Sample Preparation Kits

QuEChERS is a versatile sample preparation method for analyzing pesticides, veterinary drugs, and other residues in various sample types before GC-MS or LC-MS analysis.

<div><div><div><h3><strong>QuEChERS sample preparation—now easier, more convenient, and affordable</strong></h3><p><strong>QuEChERS</strong> (<strong><u>Q</u></strong><u>u</u>ick, <strong><u>E</u></strong>asy, <strong><u>C</u></strong>heap, <strong><u>E</u></strong>ffective, <strong><u>R</u></strong>ugged, and <strong><u>S</u></strong>afe)is a <strong>sample preparation method</strong> that was initially developed in 2003 for <strong>analyzing veterinary drugs in food</strong>. The method was also tested for <strong>pesticide residue analysis in plant material</strong> with great success. In 2003, the <strong>detailed method was published</strong> in the journal AOAC International. Since then, the QuEChERS method has evolved into a <strong>sample preparation technique used on a variety of analytes</strong> in an <strong>expanding number of sample types</strong> before analysis by <a target="_blank" rel="noopener noreferrer" href="https://www.thermofisher.com/cz/en/home/industrial/mass-spectrometry/gas-chromatography-mass-spectrometry-gc-ms.html"><strong>GC-MS</strong></a><strong> or </strong><a target="_blank" rel="noopener noreferrer" href="https://www.thermofisher.com/cz/en/home/industrial/mass-spectrometry/liquid-chromatography-mass-spectrometry-lc-ms.html"><strong>LC-MS</strong></a>.</p><p><strong>Thermo Scientific QuEChERS kits</strong> contain <strong>pre-packaged, ready-weighed salts, sorbents, and buffers</strong> to <strong>streamline your workflow</strong> and <strong>minimize the potential for error</strong>. The kits are grouped according to your <strong>analytes of interest</strong>, <strong>sample matrix</strong>, and <strong>preferred QuEChERS method</strong>:</p><ul><li><strong>Original 2003 Method</strong></li><li><strong>AOAC 2007.01 Method</strong></li><li><strong>EN 15662 Method</strong></li><li><strong>NY/T 1380-2007 Method</strong></li></ul><p><strong>Complete packages</strong>—including both <strong>extraction and clean-up kits</strong>—are available. <strong>Extraction-only and cleanup-only kits</strong> are also offered to suit your laboratory’s sample preparation needs. These <strong>pre-packaged kits save time and money</strong>, make QuEChERS procedures <strong>easier and more convenient</strong>, and ensure <strong>quality to yield reproducible results</strong> and <strong>excellent recoveries</strong> for a wide variety of analytes.</p><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Thermo_Scientific_Qu_E_Ch_ERS_Sample_Preparation_Kits_2_1e99f0c81b.jpg" alt="Thermo Scientific QuEChERS Sample Preparation Kits" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Thermo_Scientific_Qu_E_Ch_ERS_Sample_Preparation_Kits_2_1e99f0c81b.jpg 217w," sizes="100vw" width="891" height="640"></p><h3><strong>Typical QuEChERS workflow</strong></h3><div><div><div><div><div><p>As shown in the workflow diagram below, the <strong>QuEChERS method has four basic steps</strong>:</p><ol><li><strong>Homogenize sample</strong> (fruit or vegetable)</li><li><strong>Extract analytes of interest</strong> from a sample using <strong>extraction salts</strong> (pesticide residues, veterinary drugs, and/or mycotoxins)</li><li><strong>Clean-up the resulting supernatant</strong> using <strong>dispersive solid phase extraction (dSPE)</strong></li><li><strong>Analyze by GC-MS or LC-MS</strong></li></ol><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Thermo_Scientific_Qu_E_Ch_ERS_Sample_Preparation_Kits_496491ceff.jpeg" alt="Thermo Scientific QuEChERS Sample Preparation Kits" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Thermo_Scientific_Qu_E_Ch_ERS_Sample_Preparation_Kits_496491ceff.jpeg 245w," sizes="100vw" width="1170" height="706"></p><div><h3><strong>QuEChERS products</strong></h3></div><div><h4><strong>QuEChERS extraction kits for original 2003 method</strong></h4></div><div><p>The <strong>original QuEChERS method</strong> (Anastassiades et al, 2003) was developed by <strong>Steven J. Lehotay and Michelangelo Anastassiades</strong> in 2003 for the <strong>determination of pesticide residues in fruits and vegetables</strong>. The original method was created to <strong>analyze non-base-sensitive compounds</strong> and uses a <strong>sodium chloride buffer</strong> to <strong>reduce polar interferences</strong> and <strong>enhance extraction</strong>. <strong>Buffering</strong> is an important part of the QuEChERS procedure because it <strong>allows for analysis of pesticides and other residues</strong> that display <strong>pH dependence in their recoveries</strong>, depending on the <strong>sample matrix</strong>. <strong>Three different extraction kits</strong> are available to support the <strong>original 2003 QuEChERS method</strong>.</p><h5><strong>Chemicals used in the original 2003 method</strong></h5></div><ul><li><strong>Acetonitrile:</strong> Used to perform single-phase extraction (SPE) on a sample</li><li><strong>Anhydrous MgSO₄:</strong> Induces phase separation between water content in sample and acetonitrile layer during liquid-liquid partitioning step; removes remaining water from sample during dispersive solid phase extraction (dSPE) step</li><li><strong>NaCl:</strong> Induces phase separation between water content in sample and acetonitrile layer during liquid-liquid partitioning step; removes residual water from sample; reduces polar interference and enhances extraction</li><li><strong>PSA:</strong> Primary secondary amine, used to remove polar matrix components, citric co-extractives, and free fatty acids, from sample during dispersive solid phase extraction (dSPE) step</li></ul><div><h4><strong>QuEChERS extraction and clean-up kits for AOAC 2007.01 method</strong></h4><p>The <strong>AOAC 2007.01 QuEChERS Method</strong> was developed by <strong>Steven J. Lehotay and his co-workers</strong>, who <strong>modified the original 2003 method</strong> to accommodate the use of <strong>acetate buffering at higher concentration</strong> for <strong>greater buffering strength</strong>. <strong>Buffering</strong> is an important part of the QuEChERS procedure because it <strong>allows for analysis of pesticides and other residues</strong> that display <strong>pH dependence in their recoveries</strong>, depending on the <strong>sample matrix</strong>. These <strong>extraction and clean-up products</strong> here support the <strong>AOAC 2007.01 method</strong>.</p><div><h5><strong>Chemicals used in the AOAC 2007.01 method</strong></h5><ul><li><strong>Acetonitrile:</strong> Used to perform single-phase extraction on a sample</li><li><strong>Anhydrous MgSO₄:</strong> Induces phase separation between water content in sample and acetonitrile layer during liquid-liquid partitioning step; removes remaining water from sample during dispersive solid phase extraction (dSPE) step</li><li><strong>NaOAc:</strong> Buffers the sample to stabilize pH</li><li><strong>PSA:</strong> Primary secondary amine, used to remove polar matrix components, citric co-extractives, and free fatty acids, from sample during dispersive solid phase extraction (dSPE) step</li><li><strong>C18:</strong> Removes fats, sterols, and other non-polar interferences from sample</li><li><strong>GCB:</strong> Graphitized carbon black, removes pigment (<i>not recommended for use with planar pesticides</i>)</li></ul><div><h4><strong>QuEChERS extraction and clean-up kits for EN 15662 method</strong></h4><p>The <strong>extraction and clean-up products</strong> here support the <strong>EN 15662 method</strong>. <strong>Widely used in Europe</strong>, the EN 15662 method was developed by <strong>Michelangelo Anastassiades and co-workers</strong>, who <strong>modified the original 2003 method</strong> to accommodate the use of <strong>citrate buffering at a relatively low buffering capacity</strong>. This variation uses a <strong>sodium chloride buffer</strong> to <strong>minimize polar interferences</strong> in addition to <strong>sodium citrate dihydrate</strong> and <strong>disodium citrate sesquihydrate buffers</strong>. <strong>Buffering</strong> is an important part of the QuEChERS procedure because it <strong>allows for analysis of pesticides and other residues</strong> that display <strong>pH dependence in their recoveries</strong>, depending on the <strong>sample matrix</strong>.</p><h5><strong>Chemicals used in the EN 15662 method</strong></h5><ul><li><strong>Acetonitrile:</strong> Used to perform single-phase extraction on a sample</li><li><strong>Anhydrous MgSO₄:</strong> Induces phase separation between water content in sample and acetonitrile layer during liquid-liquid partitioning step; removes remaining water from sample during dispersive solid phase extraction (dSPE) step</li><li><strong>NaCl:</strong> Induces phase separation between water content in sample and acetonitrile layer during liquid-liquid partitioning step; removes residual water from sample</li><li><strong>Trisodium Citrate:</strong> Buffers the sample to stabilize pH</li><li><strong>Disodium Citrate Sesquihydrate:</strong> Buffers the sample to stabilize pH</li><li><strong>PSA:</strong> Primary secondary amine, used to remove polar matrix components, citric co-extractives, and free fatty acids, from sample during dispersive solid phase extraction (dSPE) step</li><li><strong>C18:</strong> Removes fats, sterols, and other non-polar interferences from sample</li><li><strong>GCB:</strong> Graphitized carbon black, removes pigment (<i>not recommended for use with planar pesticides</i>)</li></ul><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Thermo_Scientific_Qu_E_Ch_ERS_Sample_Preparation_Kits_3_721562526f.jpg" alt="Thermo Scientific QuEChERS Sample Preparation Kits" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Thermo_Scientific_Qu_E_Ch_ERS_Sample_Preparation_Kits_3_721562526f.jpg 245w," sizes="100vw" width="1471" height="488"></p><div><h4><strong>QuEChERS clean-up kit for NY/T 1380-2007 method</strong></h4></div><div><p>The <strong>NY/T 1380-2007 method</strong> is <strong>recommended by China Ministry of Agriculture</strong> for the <strong>QuEChERS Method sample preparation</strong> of <strong>51 specific pesticide residues</strong> in <strong>fruits and vegetables</strong> with <strong>analysis by GC-MS</strong>.</p><h5><strong>Chemicals used in the NY/T 1380-2007 method</strong></h5><ul><li><strong>Anhydrous MgSO₄:</strong> Induces phase separation between water content in sample and acetonitrile layer during liquid-liquid partitioning step; removes remaining water from sample during dispersive solid phase extraction (dSPE) step</li><li><strong>PSA:</strong> Primary secondary amine, used to remove polar matrix components, citric co-extractives, and free fatty acids, from sample during dSPE step</li><li><strong>C18:</strong> Removes fats, sterols, and other non-polar interferences from sample</li></ul></div></div></div></div></div></div></div></div></div></div></div></div>

Products from category SPE sample preparation focused on Sample Preparation - page 3

Related content

Water in GC: Safe or Risky? Here’s What You Need to Know

News from LabRulezGCMS Library - Week 20, 2026

One-shot tensor decomposition of full-scale GC×GC-VUV datasets for resolving petrochemical groups (Paul-Albert Schneide, MDCW 2026)