<p><strong>In our recent blog on </strong><a target="_blank" rel="noopener noreferrer" href="https://lcms.labrulez.com/article/5662"><strong>selecting software for targeted MS quantitation</strong></a><strong>, we outlined five key criteria labs should evaluate: simplified workflows, flexible access, scalability, regulatory readiness, and MS-native capabilities. These principles increasingly define how labs operate today, where chromatography and mass spectrometry often work hand in hand to deliver confident results— and they are foundational to </strong><a target="_blank" rel="noopener noreferrer" href="https://lcms.labrulez.com/products/76"><strong>Chromeleon 7.4 software</strong></a>.</p><p>This release reflects how analytical workflows are changing. Workflows are no longer confined to individual techniques or isolated systems. From development through QA/QC and regulated use, laboratories need consistency in how data is created, processed, reviewed, and governed across instruments, users, and sites.</p><p>Chromeleon 7.4 software supports this evolution by bringing chromatography and mass spectrometry together within a single enterprise-ready environment, helping reduce variability, strengthen compliance, and scale operations without increasing complexity.</p><h3><strong>1. Simplified data and workflow management</strong></h3><p>Quantitative workflows can generate significant volumes of data, but challenges often begin earlier, during method development. In many labs, moving from exploratory method development into validated, routine analysis still requires rebuilding methods, switching systems, or reconfiguring workflows. This adds time, variability and risk.</p><p>Chromeleon 7.4 software helps eliminate these barriers by supporting the entire analytical lifecycle — from method creation through routine acquisition, processing, and reporting, within a single, cohesive environment. This continuity reduces setup time, preserves consistency as methods evolve, and supports both development and high-throughput analysis.</p><p>Enhanced visualization tools support confident decision-making. The fragment visualization pane displays MS² and MS³ fragments alongside chromatographic traces, while integrated isotopic pattern simulation enables rapid confirmation of expected results without relying on external tools.</p><p>Together, these capabilities reduce workflow reconfiguration, enabling laboratories to minimize variability and reduce the risk of errors introduced during method transfer or routine deployment.</p><blockquote><p>See this in practice – <a target="_blank" rel="noopener noreferrer" href="https://lcms.labrulez.com/webinar/5321"><strong>Extending the dynamic range of GLP-1 quantitation using the Thermo Scientific Stellar MS and Chromeleon software</strong></a></p></blockquote><h3><strong>2. Connected, controlled, and collaborative</strong></h3><p>Today’s laboratories rarely operate under one roof. Whether across departments or global sites, teams need to collaborate while maintaining data integrity and compliance.</p><p>With centralized data access and flexible remote control, Chromeleon 7.4 software enables secure collaboration. The Business Continuity Repository enhances existing network failure protection by replicating key files locally, allowing uninterrupted operation even during server outages. Analysts stay productive, and data remains protected.</p><p>This flexibility supports hybrid work models, multi-site operations, and continuous productivity — all without compromising data control.</p><blockquote><p>Learn more in our recent webinar –<strong> </strong><a target="_blank" rel="noopener noreferrer" href="https://lcms.labrulez.com/webinar/5232"><strong>Targeted MS quantitation – controlled and accessed from anywhere</strong></a></p></blockquote><h3><strong>3. Designed for modern, scalable workflows</strong></h3><p>As analytical workloads grow and diversify, software must scale seamlessly across instruments, users, and sites.</p><p>Chromeleon 7.4 software integrates advanced MS workflows into a single platform that also supports multiple separation techniques including LC, GC, IC and CE. This allows laboratories to standardize how data is acquired, processed, reviewed, and managed.</p><p>Standardizing workflows within one platform reduces reliance on disconnected systems, supporting operational consistency and simplifying oversight for QA and IT teams. Centralized administration supports coordinated updates and uptime, while open integration capabilities enable connection to broader digital ecosystems such as LIMS.</p><h3><strong>4. Designed with compliance in mind</strong></h3><p>In regulated environments, compliance can’t be an afterthought — it must be built into the foundation. This Chromeleon release strengthens its already robust compliance framework with features that promote transparency, integrity, and control throughout the analytical lifecycle.</p><p>Built-in support for system suitability testing and controlled processing helps ensure consistent method performance throughout routine use. Enhanced audit trail policies improve visibility into data changes, while processing visibility controls ensure results are viewable only once saved — reinforcing traceability and data integrity.</p><p>By embedding quality and control into analytical workflows, Chromeleon software reinforces transparency and confidence across the data lifecycle. These capabilities support alignment with 21 CFR Part 11, EU Annex 11, and GxP guidelines — without relying on external tools or manual workarounds.</p><blockquote><p>Discover how – <a target="_blank" rel="noopener noreferrer" href="https://lcms.labrulez.com/webinar/5583"><strong>Safeguard dataset quality in LC-MS analysis with system suitability testing and intelligent run control</strong></a></p></blockquote><h3><strong>5. Enterprise-ready platform</strong></h3><p>As laboratories expand across departments and global sites, consistency becomes as important as capability.</p><p>Chromeleon software is designed to support enterprise operations through centralized administration, standardized governance across chromatography and MS workflows, data continuity protection via the Business Continuity Repository, and integration readiness with laboratory informatics ecosystems such as LIMS.</p><p>By consolidating workflows within a single CDS environment, laboratories can coordinate updates, maintain operational consistency, and support growing analytical demands — without relying on disconnected systems.</p><h3><strong>Why now?</strong></h3><p>Laboratories are under increasing pressure to manage growing data volumes, support multiple techniques, and meet rising compliance expectations — often with limited resources.</p><p>As workflows expand across teams and sites, laboratories need software that is reliable, scalable, and flexible enough to support both routine and advanced analysis without adding operational complexity.</p><p><a target="_blank" rel="noopener noreferrer" href="https://lcms.labrulez.com/products/76"><strong>Chromeleon software</strong></a> helps organizations meet these demands by providing a single, enterprise-ready platform for acquiring, managing, reviewing, and trusting analytical data — across chromatography and mass spectrometry alike.</p><ul><li>To explore how these capabilities come together in real-world workflows, take a look at our recent webinars and experience <a target="_blank" rel="noopener noreferrer" href="https://www.thermofisher.com/content/lifetech/global/en/home/industrial/chromatography/chromatography-data-systems-cds/cds-software-built-mass-spectrometry.html"><strong>Chromeleon 7.4 software</strong></a> in action.<br>&nbsp;</li><li><strong>Visit us on&nbsp;</strong><a target="_blank" rel="noopener noreferrer" href="https://www.linkedin.com/showcase/72003132/admin/dashboard/"><strong><u>LinkedIn:</u></strong></a>&nbsp;#Chromeleon #MS #Chromatography #Compliance</li></ul>

Purpose-Built Software for Quantitation Workflows – Solving Data, Compliance, and Collaboration Challenges

<p><strong>The standard uncertainty arising from random effects is often derived from repeated experiments and is quantified in terms of the standard deviation </strong><i><strong>s</strong></i><strong> of the measured values of the quantity. If it is the standard uncertainty arising from random effects on a single measurement that is required, then the observed standard deviation </strong><i><strong>s</strong></i><strong> is used without change. However, for a result which is the mean </strong><i><strong>x</strong></i><strong> of </strong><i><strong>n</strong></i><strong> measurements the standard uncertainty decreases as </strong><i><strong>n</strong></i><strong> increases, so that:</strong></p><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Eurachem_Using_repeated_measurements_to_improve_the_standard_uncertainty_equation_1_19f8f07f8f.jpg" alt="Eurachem: Using repeated measurements to improve the standard uncertainty - Equation 1" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Eurachem_Using_repeated_measurements_to_improve_the_standard_uncertainty_equation_1_19f8f07f8f.jpg 245w," sizes="100vw" width="485" height="138"></p><p>Example 1 shows how Eq (1) applies when estimating the uncertainty of a mean value, but not when considering the uncertainty of individual observations.</p><blockquote><p><strong>Example 1</strong> A volumetric pipette is calibrated with 12 measurements; the mean and the standard deviation are calculated. Eq. 1 applies to estimate the standard uncertainty of the mean value. However, when using the pipette to deliver one aliquot, Eq. 1 does not apply and the standard uncertainty due to random variation on this single measurement is the standard deviation <i>s</i></p></blockquote><p>For Eq (1) to be valid, it is a requirement that all the measurements are independent and from a stable test sample under the <strong>same</strong> measurement conditions. The measurement conditions for all the measurements could be, for example, 1) repeatability conditions, 2) intermediate precision (within laboratory reproducibility) conditions or 3) reproducibility conditions&nbsp;</p><p>It is very important to be aware that the standard uncertainty given by Eq. 1 only gives the estimated uncertainty due to random variation under the conditions of measurement under which the observations were taken, and is only strictly valid for independent observations.&nbsp;</p><p>It can be hard to decide whether observations are sufficiently independent for Eq. 1 to apply, as there is no simple, general, rule. The following paragraphs therefore give examples of different circumstances to help identify circumstances when Eq. 1 can safely be used.</p><h3><strong>Example where Equation (1) applies&nbsp;</strong></h3><h4><strong>Measurement of inhomogeneous samples&nbsp;</strong></h4><p>If inhomogeneity for test samples is a major part of the uncertainty the analyst may choose to measure more test portions from each test sample in order to reduce the standard uncertainty. If all these measurements are made under repeatability conditions, i.e. the same measurement conditions following the whole procedure, including repeated random sampling from the test sample, the standard deviation of the mean, given by Eq. (1), should be used to estimate the uncertainty arising from variation under repeatability conditions.&nbsp;</p><h3><strong>Examples where Equation (1) does not apply&nbsp;</strong></h3><p>The following paragraphs give two examples where neither the standard deviation nor the standard deviation of the mean can be directly applied without further analysis of the data.&nbsp;</p><h4><strong>Measurements taken in groups&nbsp;</strong></h4><p>One example is when we have data from internal quality control from a measurement procedure that includes a calibration before analysis each day. We want to calculate the standard uncertainty of the mean value used to set the central line in the QC chart. The data consist of duplicate QC measurements performed on a stable test sample each day over a longer period of time (say, <i>p</i> days), giving a total of 2<i>p</i> observations; that is, <i>p</i> groups of two measurements. Because each pair of duplicate measurements has a single calibration error in common; the duplicates within the data set are not strictly independent and Eq. (1) cannot be directly used for all 2<i>p</i> observations. The uncertainty of the mean can most easily be calculated by taking the standard deviation of the <i>p</i> means for each day and dividing that standard deviation by <i>√p</i> . Analysis of variance can also be useful in similar cases. Similar principles apply to other kinds of grouping, including grouping by operator, instrument etc.&nbsp;</p><h4><strong>Measurement when the test item or measurement system is not stable over time</strong></h4><p>Another common example is time dependent data. The time dependence could be due to instrument drift or to actual change in concentration by time. In such cases the error for a given observation is partly random and in part ‘carried over’ from the previous observation. Again the errors affecting each observation are not independent because some part of the error is common to successive observations; Eq. (1) can not be used and more complex statistical techniques, that allow for correlation, must be used to process the data.&nbsp;</p><p>For further guidance on the treatment of correlated data in uncertainty evaluation, see <strong>Eurolab Technical Report 1/2006</strong>: Guide to the Evaluation of Measurement Uncertainty for Quantitative Test Results, Appendix A.5</p>

Using repeated measurements to improve the standard uncertainty

<p><strong>Our Library never stops expanding. What are the most recent contributions to LabRulezGCMS Library in the week of 27th July 2026? Check out new documents from the field of the gas phase, especially GC and GC/MS techniques!</strong></p><blockquote><p><span style="font-size:20px;">👉 </span><a target="_blank" rel="noopener noreferrer" href="https://gcms.labrulez.com/library"><span style="font-size:20px;"><strong>SEARCH THE LARGEST REPOSITORY OF DOCUMENTS ABOUT GCMS AND RELATED TECHNIQUES</strong></span></a></p></blockquote><blockquote><p><strong>👉 Need info about different analytical techniques?</strong> Peek into <a target="_blank" rel="noopener noreferrer" href="https://lcms.labrulez.com/library"><strong>LabRulezLCMS</strong></a> or <a target="_blank" rel="noopener noreferrer" href="https://icpms.labrulez.com/library"><strong>LabRulezICPMS</strong></a> libraries.</p></blockquote><p>This week we bring you application notes by <strong>Agilent Technologies </strong>and<strong> Thermo Fisher Scientific, </strong>poster by <strong>MDCW / University of Washington </strong>and brochure by <strong>Shimadzu!</strong></p><h3><strong>1. Agilent Technologies: Routine Trace‑Level Analysis of m‑Xylene in High‑Purity p‑Xylene</strong></h3><p><strong>Using the </strong><a target="_blank" rel="noopener noreferrer" href="https://gcms.labrulez.com/library?mainauthorItems=10&amp;search=8890B"><strong>Agilent 8890B GC system</strong></a></p><ul><li>Application note</li><li><a target="_blank" rel="noopener noreferrer" href="https://gcms.labrulez.com/labrulez-bucket-strapi-h3hsga3/an_trace_analysis_m_xylene_high_purity_p_xylene_5994_9329en_agilent_508bcfb48c.pdf"><strong>Full PDF for download</strong></a></li></ul><section><div><div><div><div><div><div><p>The Agilent 8890B GC system builds on the exceptional performance of the Agilent 8890A GC, with the addition of many features designed to enhance the user experience for both new and expert‑level operators. This application note explores several use cases of these features applied to a challenging GC purity method—quantifying trace‑level m‑xylene (MX) in p‑xylene (PM). This separation requires careful balancing of optimized chromatographic parameters— speed, resolution, and sensitivity. Leveraging Agilent GC Assist features, including early maintenance feedback (EMF) counters and automated peak evaluation capabilities integrated into the 8890B GC, helps maximize method robustness and instrument uptime.&nbsp;</p><p>Though conceptually simple, separating and measuring small quantities of m‑xylene in p‑xylene is a challenge that requires precise instrument control and the highest‑quality GC parts and consumables. As both compounds are positional isomers and have nearly identical boiling points, separation has historically been achieved using a long and highly polar column, such as a polyethylene glycol "wax" phase. ASTM D7504 recommends a wax column with dimensions 60&nbsp;m × 0.320 mm and 0.25 µm phase thickness. A 0.50 µm phase thickness can be used for increased resolution.1 The separation is validated with a p‑xylene standard containing approximately 1,000 ppm m‑xylene. Measuring m‑xylene at significantly lower concentrations requires an increase in resolution between MX and PX, which can be accomplished by increasing the phase thickness of the column at the cost of increased peak broadening. This broadening negatively impacts the limit of detection (LOD) and the limit of quantification (LOQ) for MX and must be offset by reducing the inner diameter of the column to resharpen the peak. This application note demonstrates the use of 0.200 mm and 0.100 mm id wax columns to yield optimized separations, presenting the associated benefits and limitations of both&nbsp;separations.</p><h4><strong>Experimental</strong></h4><p>An <a target="_blank" rel="noopener noreferrer" href="https://gcms.labrulez.com/library?mainauthorItems=10&amp;search=8890B"><strong>8890B GC</strong></a> was configured with an <a target="_blank" rel="noopener noreferrer" href="https://gcms.labrulez.com/library?mainauthorItems=10&amp;search=7650A"><strong>Agilent 7650A automatic liquid sampler</strong></a> (ALS), split/splitless (SSL) inlet, and flame ionization detector (FID). Two columns were used to explore two different separation speeds—a faster separation with less sample capacity using an Agilent J&amp;W DB‑WAX&nbsp;FF column, 20 m × 100 µm, 0.2 µm (p/n 127‑7023FF) and a higher‑resolution separation with more sample capacity using an Agilent <a target="_blank" rel="noopener noreferrer" href="https://gcms.labrulez.com/library?mainauthorItems=10&amp;search=J%26W+HP%E2%80%91INNOWax"><strong>J&amp;W HP‑INNOWax</strong></a> column, 50 m × 200 µm, 0.4 µm (p/n 19091N‑205I). Both methods used hydrogen carrier gas, and Agilent Gas Clean filters were used to remove moisture, hydrocarbons, and oxygen from the carrier gas and FID hydrogen. The FID air was filtered for moisture and hydrocarbons. The GC configuration and method details can be found in Tables 1 and 2, respectively.</p><h4><strong>Results and discussion</strong></h4><p>Establishing and ensuring the method’s long‑term stability requires protecting the column stationary phase by limiting the amount of oxygen in the system. While carrier gas contamination is typically the largest source of unwanted oxygen, the inlet septum can also contribute to oxygen ingress as successive syringe injections create a hole, necessitating regular changing. The Agilent portfolio of consumables and supplies has several solutions specifically designed to overcome these challenges. The Gas Clean purification system features a carrier gas filter that removes oxygen, moisture, and hydrocarbons and includes a color‑changing visual indicator of filter life, which can be monitored remotely by the 8890B GC using an optional optical sensor. Advanced Green septa are engineered for low bleed and extended durability, further enhanced by using a Blue Line autosampler syringe with a tapered needle to reduce physical coring of the septum. Regular maintenance of these parts maximizes instrument uptime. The 8890B GC has several features designed to warn when maintenance is approaching, assist when maintenance is required, and track when maintenance is completed.</p><p>The 8890B GC features intelligent tracking of the ages of consumables using injection‑ and time‑based counters. These EMF counters feature two optional warning thresholds—"Service Warning" and "Service Due"—that are user‑configurable and function like the oil light on the dashboard of a vehicle, telling users of approaching maintenance. The EMF counters can be accessed directly through the GC touchscreen or through the GC Assist interface. Figure 1 shows an overview of the EMF counters for the front inlet, and Figure 2 presents the detailed history of septum maintenance, including a running tally of injections on the current septum. When performing maintenance on the 8890B GC using the guided maintenance process on the touch screen or GC Assist interface, the EMF counters are automatically reset at the end of the procedure and can also be reset manually. For this application, the EMF counters and appropriate warning thresholds for the septum, liner, syringe, column, inlet gold seal, and carrier gas filter will be explored.</p><h4><strong>Conclusion</strong></h4><p>The Agilent 8890B GC system—powered by the highest‑quality Agilent columns and supplies—delivers a robust, sensitive solution for measuring trace‑level m‑xylene (MX) in p‑xylene (PX). The Agilent J&amp;W HP‑INNOWax column produced the highest‑resolution separation and the best retention time stability, with an S/N ratio of 98.5 for 50&nbsp;ppm MX. The narrower Agilent J&amp;W DB‑WAX FF column yielded a 40% faster run time at the cost of lower resolution and retention time stability, with an S/N ratio of 27.7 for 50&nbsp;ppm MX. The integrated Agilent GC Assist features, peak evaluation and early maintenance feedback (EMF) counters, provide intelligent, automated monitoring of system and separation health, maximizing instrument uptime and supporting long‑term success with routine trace analysis.</p><h3><strong>2. MDCW / University of Washington: Developing 2D mzCompare for single GC×GC-TOFMS chromatograms: Substantial resolution enhancement in the context of statistical overlap theory</strong></h3><ul><li>Poster</li><li><a target="_blank" rel="noopener noreferrer" href="https://gcms.labrulez.com/labrulez-bucket-strapi-h3hsga3/P_4_Wenjing_899f31a19e.pdf"><strong>Full PDF for download</strong></a></li></ul><section><div><div><div><div><div><div><p>Accurate identification of all detectable analyte components in a single comprehensive twodimensional (2D) gas chromatography time-of-flight mass spectrometry (<strong>GC×GC-TOFMS</strong>) chromatogram is a fundamental interest in the field. Herein, we developed a new algorithmic software approach called 2D mzCompare to generate accurate peak tables for GC×GCTOFMS. Extending from our original method for one-dimensional GC-MS data, the 2D mzCompare algorithm discovers selective mass channels (m/z) for each analyte to resolve overlapping peaks and improve analyte identification, leveraging the similarity in retention time and peak shape across m/z of the same analyte. The 2D mzCompare algorithm calculates the peak shape similarity between m/z at every modulation via lack-of-fit (LOF), followed by clustering and focusing steps, to generate a final peak table. To evaluate this software, we simulated realistic GC×GC-TOFMS data in the context of the statistical overlap theory (SOT), so the exact number and identities of analytes are known a priori. Utilizing an in-house mass spectrum library of similar compounds, GC×GC-TOFMS chromatograms were simulated with varying degrees of chromatographic saturation (𝛼2𝐷). First, we provide a new algorithmic approach, 2D mzCompare, to resolve overlapped analytes in GC×GCTOFMS data, and second, we validate the accuracy of the software performance using SOT.</p><h4><strong>Conclusions and Future Work</strong></h4><p>An extended algorithm, 2D mzCompare designed for intra-chromatogram comparison to enable rigorous analyte discovery and identification, was developed for GC×GC-TOFMS data. Within the context of SOT, 2D mzCompare increases separation resolution by computationally minimizing the 2D peak widths, enhancing 2D peak capacity and reducing the saturation factor. At low saturation factors (𝛼2𝐷= 0.01, 0.03, and 0.1), over 95% of the simulated components are found to be mathematically resolved singlets (pure analyte components) by 2D mzCompare, while approximately 62% were found at 𝛼2𝐷 = 1, exceeding predictions made by SOT. Using optimized 2D mzCompare parameters, improvements in 2Rs and 𝛼2𝐷 are about 12-fold, empirically validating SOT expectations. Furthermore, 2D mzCompare can be used as a preprocessing tool to determine or validate the “rank” (the number of analyte components) in overlapped regions of GC×GC-TOFMS chromatograms when combined with chemometric methods such as MCR-ALS or PARAFAC. Future studies will focus on applying the algorithm to real sample datasets.</p><h3><strong>3. Shimadzu: Meet The World’s First Multi-Mode FID In </strong><a target="_blank" rel="noopener noreferrer" href="https://gcms.labrulez.com/library?mainauthorItems=1&amp;search=GC-2060"><strong>Nexis GC-2060</strong></a></h3><ul><li>Brochure</li><li><a target="_blank" rel="noopener noreferrer" href="https://gcms.labrulez.com/labrulez-bucket-strapi-h3hsga3/s_gc_f33_3f7f48eead.pdf"><strong>Full PDF for download</strong></a></li></ul><h4><strong>High Performance And Low Maintenance Multi-Mode FID&nbsp;</strong></h4><p>The new FID-U (2.0) in the Nexis <a target="_blank" rel="noopener noreferrer" href="https://gcms.labrulez.com/library?mainauthorItems=1&amp;search=GC-2060"><strong>GC-2060</strong></a> reengineers conventional FID to maximize uptime and efficiency. With new Air and O2 makeup gas options, you can streamline your gas supply – saving cylinder costs and lab space. Its capabilities can be further expanded with Shimadzu’s proprietary Jetanizer and Polyarc microreactors.</p><h4><strong>Cylinder-Free FID Operation With Hy/Ox and Hy/Air Modes</strong>&nbsp;</h4><p>Routine operation with traditional FIDs is often costly and complex, requiring a three-gas setup: a He or N<sub>2</sub> makeup gas combined with H<sub>2</sub> and Air. The new FID simplifies your infrastructure by introducing Air and O<sub>2</sub> as makeup gas alternatives, unlocking true cylinder-free operation.* This helps to reduce running cost and cut helium usage.</p><h4><strong>Keep Your Bench Space As You Expand Your Analyte Coverage&nbsp;</strong></h4><p>Seamlessly integrate Jetanizer and Polyarc microreactors to boost detector response for weak or undetectable compounds. The new FID delivers simpler quantitation and broader analysis capabilities with zero extra footprint.</p><h4><strong>Jetanizer Mode (CO and CO2 Detection)&nbsp;</strong></h4><ul><li>Converts CO and CO2 to CH4 for detection&nbsp;</li><li>Enabled by simply replacing the FID nozzle&nbsp;</li></ul><h4><strong>Polyarc Mode (Single-Calibration Approach)&nbsp;</strong></h4><ul><li>Converts hydrocarbons, CO and CO2 to CH4 for detection&nbsp;</li><li>Provides universal response across compounds&nbsp;</li><li>Quantitates the above using just one calibration curve</li></ul><h3><strong>4. Thermo Fisher Scientific: Measuring destruction efficiency of greenhouse gases released by semiconductor fabrication tools</strong></h3><ul><li>Application note</li><li><a target="_blank" rel="noopener noreferrer" href="https://gcms.labrulez.com/labrulez-bucket-strapi-h3hsga3/AN_54654_MAX_i_R_Semi_Febrication_EN_9ce9475305.pdf"><strong>Full PDF for download</strong></a></li></ul><h4><strong>Background&nbsp;</strong></h4><p>Modern materials processing activities involve the use of cold plasmas employing fluorinated gases as reactive species. Some of these gases have been demonstrated to exhibit deleterious environmental consequences resulting in their being labelled as greenhouse gases or GHGs. Among the list of GHGs undergoing intense review are those of fluorinated gases, such as NF<sub>3</sub>, CF<sub>4</sub> , SF<sub>6</sub>, CH<sub>2</sub>F<sub>2</sub> , etc. Many of these gases are either reactants or are generated as by-products of semiconductor wafer fabrication processes, such as etching and chemical vapor deposition. Therefore, semiconductor fabrication plants (SemiFabs) employ abatement tools to destroy and dilute these fluorinated gases before they reach a stack scrubber. This process assures that they will meet EPA regulations which require yearly facility-dependent GHG emission audits. European and Asian semiconductor manufacturers must meet similar regulations as well.&nbsp;</p><h4><strong>Problem&nbsp;</strong></h4><p>To ensure that the abatement process occurs efficiently, SemiFabs are required to audit selected abatement devices (one per each wafer processing tool employed) such that each device gets periodically reviewed for efficiency in destroying these GHGs before they are released to the scrubber. Since there are hundreds of abatement devices within a single SemiFab, the monitoring process must be accurate, fast (one or two hours), and able to monitor multiple fluorinated species simultaneously. Most SemiFabs utilize a series of devices to perform the necessary measurements required to calculate an overall destruction efficiency for each fluorinated species. Among the measurements required are the dilution factor (the overall ratio of the flowrate into the abatement device to that of the flowrate out of the abatement device). In most cases, this requires the use of a krypton gas tracer and a mass spectrometer (for measurement of flowrate out) in addition to an FTIR to measure a separate infrared-active gas tracer (for measurement of flowrate in). Also required is another more sensitive FTIR to measure the residual fluorinated gases which survived destructive processes within the abatement device. The result is a very bulky and cumbersome system to measure input and output flows and concentrations. What is needed is a much simpler and fully integrated measurement system capable of performing ALL these tasks.</p><h4><strong>Solution&nbsp;</strong></h4><p>Thermo Fisher Scientific has developed a new methodology for measuring abatement destruction efficiencies with a much simpler system. The system uses the <strong>Thermo Scientific™ MAX-iR™ FTIR Gas Analyzer</strong> with DTGS detector in conjunction with the <strong>Thermo Scientific™ Automated Sample Console (ASC-10™)</strong>. The MAX-iR analyzer can monitor the entire IR spectral range (500-5000 cm-1) without the need for liquid nitrogen. The ASC-10 allows for the precise measurement of post-abatement flow by determining the dilution of a tracer infrared gas or gases; this obviates the need for a spacious and costly mass spectrometer and krypton gas utilized in the previous system.</p></div></div></div></div></div></div></section></div></div></div></div></div></div></section>

News from LabRulezGCMS Library - Week 31, 2026

Software

Article

Product

Application

Academy

Poster

A unique company dedicated to serving science helping our customers drive productivity and accelerate results. Through our premier brands – Thermo Scientific, Applied Biosystems, Invitrogen, Fisher Scientific and Unity Lab Services.

Thermo Fisher Scientific

Eurachem is a European network promoting international traceability of chemical measurements and good analytical practice. It provides expert guidance, supports method validation, uncertainty evaluation, proficiency testing, and facilitates discussion on technical and policy issues in analytical quality.

Eurachem

Everything from the world of analytical chemistry in one place. We connect people in solving their problems. At Labrulez you will find all the necessary information easily, quickly and clearly. Stop searching and start finding.

LabRulez

Millipore Milli-Q-System Q-POD/IQ7000 Water Dispenser (Tested)

The Milli-Q® IQ 7000 with Q-POD® dispenser delivers consistently high-quality Type I ultrapure water for critical laboratory applications. It combines precision dispensing, integrated TOC monitoring, complete data traceability, remote system management, and compliance with major international water quality standards.

Millipore Advantage A10 Water Purification System with Q-POD® Dispenser (Refurbished)

Milli-Q Advantage A10 with Q-POD delivers 18.2 MΩ·cm ultrapure water with continuous TOC monitoring and ergonomic point-of-use dispensing for advanced analytical and life-science workflows.

Marketplace products from category Type 1 water from LabRulez - page 1

Related content

News from LabRulezGCMS Library - Week 31, 2026

Purpose-Built Software for Quantitation Workflows – Solving Data, Compliance, and Collaboration Challenges

Using repeated measurements to improve the standard uncertainty